Jump to content
SAU Community

Recommended Posts

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

now you're talking!! but sadly I have no idea of anyone who'll have a car like that. as far as I know in aus sports sedans if you wanted to run an AWD, turbo car in sports sedans it had to retain the factory floor-pan ie no space frame in combo with FI and AWD. plenty or RWD, NA, V8 spaceframe getting around though.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4551490
Share on other sites

our rules specify that an AWD vehicle must run the factory floor pan so you won't find a space frame GTR here.

Mine is probably as close as you'll get to a space frame GTR. It retains the original floor pan but thats about it everything else has been cut out and the cage is the cehicles strength.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4551930
Share on other sites

i guess that i can convert an exsisting frame to accept the RB even if i dont run the 4wd i dont think that would be an issue for me.

Makes it easier to dry sump i guess. I did see a car on this forum being prepare and i am not sure if that was yours Risking.

Which site would i be best look at to find a doner car?

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4552127
Share on other sites

Duncan,

it seems we are going to be heading down the route of GT3 And GT4 which i really dont want to be butting heads with GT3 cup cars.

They are also running a class simular to the 24 hours regs, which allow space frame cars and any that fall outside GT3 & 4 and THAT is more to my liking.

Even though were are currently converting a lotus elise to GT3 spec but with a K20 honda engine, i still like the idea of a space frame car.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4552140
Share on other sites

A well sorted GTR will definatly be able to give it to the cup cars for sure.

I know as I have built one.

Built it for a mate of mine rego 26r32 and he was quicker around bathurst on semi's than Peter Fitzgerald in a cup car on slicks at the drive Bathurst event in december last year and the car has a lot more in it yet. Just for those that do not know Peter fitzgerald has raced cup cars very successfully for a lot of years and is no slouch behind the wheel.

He was also quicker than a GT2 that was stnd and ran about the same pace as a GT2 that was extensivly modified all of the cars mentioned were on full slicks to. We have footage from the camera mounted on the boot of the car i will upload it for you guys to have a look in the next day or so.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4552415
Share on other sites

try as i might i cant get close to these things, the GT3RS yes but the heavily modified GT2, Z06 and viper are just to bloody quick of which my old banger will be lumped into as its not GT3 or 4. I am no slouch behind the wheel either i have national karting championships etc. But i am truely all at sea with this car and getting to do as i want. I love the old engine even with its issues but to have a space frame car with the RB 26 in it would tick all the boxes for me.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4552443
Share on other sites

an existing space frame chassis would be the best place to start if thats your chosen path.

You could always do a semi space frame like mine, the cage is very intense and all sheet metal is redundant but left there to keep the rule makers happy.

I have considered buying the Prelude with an SR20 and replacing it with my dry sumped RB with holinger RWD only obviously.

The biggest issue is modifications to the space frame can become a pain if the 4 cylinder is a tight fit to begin with.

Link to comment
https://www.sau.com.au/forums/topic/266722-sports-sedan/#findComment-4553454
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
×
×
  • Create New...