Jump to content
SAU Community

Recommended Posts

Mate, I hope you do get something extra for having a Nismo ECU :blink: . You'd have to be annoyed at paying money for nothing more than you could get by cutting a wire.

Surely Nismo don't just disable that input and sell it for $800 or whatever?? That would be a huge scam if that was the case lol.

I can tell you this....If I put the Standard ECU or Impul on my car with the turbo I have on it its a Fat Black laggy POS.....4,800rpm before boost starts to climb. With the Nismo it was full boost by about 4,200rpm before the tune.....after the tune full boost by 3,200RPM and Cihan pulled some timing out because it was too reactive.

Kickdown has also been played with!

oh and I can do more than 171.5km/h. :P

I'll lay London to a brick that if a Nismo came up on IM you guy's would be all over it!.....it's the best plug and play mod you can get!...snipping the wire just let's you do burnout's!....well maybe not for Aaron :P

Edited by Jetwreck

I can tell you this....If I put the Standard ECU or Impul on my car with the turbo I have on it its a Fat Black laggy POS.....4,800rpm before boost starts to climb. With the Nismo it was full boost by about 4,200rpm before the tune.....after the tune full boost by 3,200RPM and Cihan pulled some timing out because it was too reactive.

Kickdown has also been played with!

oh and I can do more than 171.5km/h. :P

I'll lay London to a brick that if a Nismo came up on IM you guy's would be all over it!.....it's the best plug and play mod you can get!...snipping the wire just let's you do burnout's!....well maybe not for Aaron

i dont think it would still let anyone with a highflow do burnouts(stock ecu that is). without a high stall its only a little bit better...

i think my next challenge is to disable the attessa with a switch, and still be able to keep ABS.. the plug under the dash puts the 4WD light on, but i think it reacts the same and pushing the "synchro" switch.

which leads me to believe there is clearly more to the ECU than a throttle opening..

i dont think it would still let anyone with a highflow do burnouts(stock ecu that is). without a high stall its only a little bit better...

i think my next challenge is to disable the attessa with a switch, and still be able to keep ABS.. the plug under the dash puts the 4WD light on, but i think it reacts the same and pushing the "synchro" switch.

which leads me to believe there is clearly more to the ECU than a throttle opening..

You need awesome installed!thumbsup.gif

i dont think it would still let anyone with a highflow do burnouts(stock ecu that is). without a high stall its only a little bit better...

i think my next challenge is to disable the attessa with a switch, and still be able to keep ABS.. the plug under the dash puts the 4WD light on, but i think it reacts the same and pushing the "synchro" switch.

which leads me to believe there is clearly more to the ECU than a throttle opening..

One of my test launches yesterday (with brake switch disconnected) caused the 4WD light to come on :whistling:, but this mod doesn't mean instant burnouts.

Our ECU's are very much like women; I don't think any of us guys really understand how they work, but we know what we'd like them to do better, LOL

One of my test launches yesterday (with brake switch disconnected) caused the 4WD light to come on :whistling:, but this mod doesn't mean instant burnouts.

Our ECU's are very much like women; I don't think any of us guys really understand how they work, but we know what we'd like them to do better, LOL

LOL

yeh theres a plug attached to the OBD port, this is 'meant' to disable the 4WD. unplugging it certainly turns the 4WD light on, but it felt more so of 50/50 distro as i couldnt spin the wheels up at all and it was wet. but it definitely pulled as if the roads were dry..

i want more of a 0/100 lol

LOL

yeh theres a plug attached to the OBD port, this is 'meant' to disable the 4WD. unplugging it certainly turns the 4WD light on, but it felt more so of 50/50 distro as i couldnt spin the wheels up at all and it was wet. but it definitely pulled as if the roads were dry..

i want more of a 0/100 lol

why don't you try one of these then....use to have one on our old R32 GTR....worked very well.

http://www.ebay.com....=item19c5b4b24f

sent off a question asking them if it works for the M35.

Would like to see what our cars would run on the Dyno just in RWD!!!

Edited by Jetwreck

it would be something I could consider..

but i wouldnt know where to start with wiring it in succesfully I cant seem to find a diagram for our attessa wiring system..

but isnt that more for being able to split torque to the front when you want instead of when needed.

it says that normal mode is just 'stock'

it would be something I could consider..

but i wouldnt know where to start with wiring it in succesfully I cant seem to find a diagram for our attessa wiring system..

but isnt that more for being able to split torque to the front when you want instead of when needed.

it says that normal mode is just 'stock'

FFS!....isn't that what you want.....man your sizzled :P

It does for me. :)

Haha, yeah I know for a few of you guys it does. I was meaning for the majority of us with minimal mods, but you knew that & were just showing off ! LOL

why don't you try one of these then....use to have one on our old R32 GTR....worked very well.

http://www.ebay.com....=item19c5b4b24f

sent off a question asking them if it works for the M35.

Would like to see what our cars would run on the Dyno just in RWD!!!

I enquired about this one a while ago & it's never been used in a M35 yet. I can't see why it wouldn't work with our cars, but.....

OK, found the message:

"As far as I know no one is using one on an M35. If you want to take some photos of the G-sensors and connector under the center console I can certainly tell you if it is likely to work and I would be willing to refund your unit if it turned out not to be suitable after trying.

Regards Justin"

I really wanted more front wheel torque for those wet days when you want to get where you're going quicker & with less RWD "fun".:happy:

Edited by Commsman

I enquired about this one a while ago & it's never been used in a M35 yet. I can't see why it wouldn't work with our cars, but.....

OK, found the message:

"As far as I know no one is using one on an M35. If you want to take some photos of the G-sensors and connector under the center console I can certainly tell you if it is likely to work and I would be willing to refund your unit if it turned out not to be suitable after trying.

Regards Justin"

I really wanted more front wheel torque for those wet days when you want to get where you're going quicker & with less RWD "fun".:happy:

dont you have a synchro button?

dont you have a synchro button?

Yes I do :yes: But so what?

You're going to tell me that using syncro will engage proper 4WD, right?... Well when I do that it feels like I'm driving a 4WD with the front hubs locked. You know, harder to turn in tight spaces etc. What I want is partial or progressive front wheel torque, without the "lock up" feel.:huh:

LOL

yeh theres a plug attached to the OBD port, this is 'meant' to disable the 4WD. unplugging it certainly turns the 4WD light on, but it felt more so of 50/50 distro as i couldnt spin the wheels up at all and it was wet. but it definitely pulled as if the roads were dry..

i want more of a 0/100 lol

did you unplug it and pump the break pedal 5 times?

Yes I do :yes: But so what?

You're going to tell me that using syncro will engage proper 4WD, right?... Well when I do that it feels like I'm driving a 4WD with the front hubs locked. You know, harder to turn in tight spaces etc. What I want is partial or progressive front wheel torque, without the "lock up" feel.:huh:

lol yehhhhmellow.gif

i liked it, mine doesnt feel to jittery

did you unplug it and pump the break pedal 5 times?

yeh it doesnt do anything.. but i figured out full time RWD read the attesa thread.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
    • OK, if it idles at 1000+ with the AAC, its not an idle airflow problem. The cold start valve just gives extra air when the engine is cold, but you have enough air without it to idle at 1000. I think you are back to a fuel problem, sorry. Can you see the fuel pressure staying constant or does it drop as the revs drop to a stall?  
×
×
  • Create New...