Jump to content
SAU Community

Recommended Posts

if you've only got 5k it will be pretty tight. The only real option is to buy something already built.

go here and look for anything where the asking price is 10k. offer them 5 and voila you have a track car.

http://www.my105.com.au/default3.asp?id=39...sortby=PriceASC

expect it to need work but at least it will come with the wheels/suspension/cage/seats/belts that you need.

heres some, first couple are the best bet I think

http://www.my105.com.au/classified.asp?id=11481

http://www.my105.com.au/classified.asp?id=11022

http://www.my105.com.au/classified.asp?id=10241

http://www.my105.com.au/classified.asp?id=10679

not prepared but a good choice for under 2l categories if you have the extra 10k to finish it

http://www.my105.com.au/classified.asp?id=10814

http://www.my105.com.au/classified.asp?id=10996

http://www.my105.com.au/classified.asp?id=11646

R31, with vlt conversion and s13 suspension, r32 brakes. would be right on the limit of your budget but doable i think.

either that or an old corolla, be it older rwd, or later fwd model. early civics are a chance too

bike? or one of those small things that use bike engines but look like V8 supercars. how much are they worth?

Yeah 5k there isnt much out there...

Bobby's answer is the best, go kart and plenty left for a trailer and parts and fuel :laugh:

Otherwise....

If 5k is your budget, its really an r31/vl non turbo, then suspension and brakes and exhaust and intake. Strip what you dont need. might have some $ left for a seat and harness

weld the diff.

Can do the same for the KE70 rolla's.

you'd be hard pushed to buy an mx5 for 5k or under.

edit - you'll need good tyres too...that'll limit costs..

series 2 nissan bluebird 910 sedan about $1000 for a good example

-2ltr high compression L4

-5 speed manual

-elec ignition standard

-elec fuel pump standard

-therno fan standard

fit s13 coilovers and brakes to the front and coilovers to the back about $1500

r31 front brakes are a bolt for bolt mod (if s13 det brakes are not used instead - $500 from coilovers and add about $150)

r31 or s13 front sway $30

Good clutch $150

TRX and LX had the disk rear end (range from $150 - 300 if fitting afterwards)

dif is a bit weak so upgrade to the later h190 dif out a series 3 bluebird then weld it (centres for either h165 or h190 are about $75 to 100 each but need the right beam axle for centre - see above cost - less for drum of course)

save up and fit twin 45mm webers ($1000) or slot a ca18, sr20, z18 or fj20 in with nothin but a soldering iron and a spoon - you may need to fit a series 3 ca20s 910 front cross member for ease of fitment

S13 turbo 15 inch x 6 inch mags $200

all out a quick easy build will cost about $4100

factor in harness, seat, semi tyres, roll cage and strut brace... but they are irrelevant depending on racing type and most of the above can be sourced for less if you pick up a s3 trx or a less than prime example

wouldn't hurt for fresh rings and bearings in the old L20 after 25 years

subtract spare wheel, interior, sound deadening, unnecessary electrics, bumpers if necessary you will be under 1000kg easily (about 1100kg standard)

Edited by 910trx

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...