Jump to content
SAU Community

Recommended Posts

Now i never thought the day would come but......the old girl keeps throwing flames and I'm not sure if it's right as it's happening too often. I think that over time it is getting worse. Symptoms. You do redine gear changes and everything is hot, it blows flames when you lift to change (I'm not unhappy with that). The bit that concerns me is that some mid rpm gear changes it still carries on. Even when it's not blowing flames (big ones) I've had feedback (not from the law TG) that there are little flickering ones visible within the pipe. On a light throttle, tipping in or out, there's a lot of popping and banging going on from the pipe. It all sounds like unstable and incomplete combustion.

Now, I've replace the coilpacks (Splitfire) about 9 months ago and it is making plenty (more than ever actually) of power with no misfire under boost and acell. I run a high flow cat (or at least I've been charged for one), stock dumps and a 3.5" SS system and about 25lb of boost. It's a built engine running forged pistons with about 15k kms on it.

Any qualified people want to give me a steer as to what's happening.

I used to love it and try and make the car do it for my own fun, but now it seems it's happening no matter what....

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/
Share on other sites

Disclaimer: I am NOT qualified to reply to this thread, but I'm waiting for my morning coffee so that I can be productive.

Obviously the root cause if your engine overrunning it's fuel, fuel hitting the red hot exhaust and causing the pretty orange lights.

I assume it's not tuned to run stupidly rich? Your injectors aren't leaking are they? They could be dumping fuel on the exhaust combustion stroke.

The first thing though, is that your cat usually blocks any visible flames, so if you're seeing flames out your exhaust, I'd check that your expensive high flow cat hasn't melted into a molten mess.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557951
Share on other sites

Thanks Andrew. Disclaimer noted. It is tuned to run rich cos it has lots of boost, but stupidly so?.....I'd have to ask the tuner and I doubt he'll say it is stupid. Injectors are new 2 years ago (Tomei 700cc - I think) so I doubt they're leaking.

I'm suspecting it's over-fuelled and possibly ignition retared. If you were an engine builder would you under-fuel and advance ignition under 25lb.....? 305 RWKW isn't that much for my set up considering the boost, so that also leads me to the same thought....

How to check for melted CAT? More to the point, what CATs do not melt? Maybe another question is under what conditions do CATs melt and are there CATs out there that handle tuned GTRs.

More hypotheses please!

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557967
Share on other sites

You're running 25psi and only making 305 rwkw?

Obviously there are many, many factors involved, but as a rough guide, that seems a little low to me.

Even with tiny GT-SS turbos and stock headwork (260 poncams), running 20-21psi, my old GTR made 320awkw (340rwkw?) on CRD dyno (not known for reading stupidly high)

Engine tuners will make an engine run rich to use the fuel to cool down the cylinders and control detonation, at the expense of fuel consumption and reduced power.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557995
Share on other sites

In my experience...

The most common causes of flames I have seen (in order) are:

1. No cat (track days destroy cats.. (I had one blow out the exhaust down the straight a flaming molten lava)

2. Injectors aren't switched off on decel

3. Exhaust leak- because you need oxygen and the engine has used up most of it when it combusted it not as easy for it to ignite and hence only happens at full noise when the car isn't using every last bit of it and the exhaust is red hot. When you have an exhaust leak, on decel the engine goes into vacuum and the exhaust sucks (through the gasket leaks) fresh air.. combine that with a red hot exhaust and you get flames even at partial/mid throttle. (in addition obviously to the fresh air (hot once its gone through the motor) being sucked through the engine on decel).

I would put my money in your case as being likely being a combination of all three. Cats don't last long when you are making big power (1.6 bar +GTSS's suggests to me your making a bit ;-) ) as they just get too hot and I wouldn't be surprised if your injectors are not turning off.

Diagnosis

1. Stick your arm underneath the car and give it a good bash with your fist. If it rattles then its obviously self explanatory, its a dull sound then might be all good and if its sounds empty then that would suggest you no longer have one. Otherwise just take it out yourself its really easy. Alternatively, take it to an exhaust shop. Shouldn't cost much at all for them to take it out and put it back.

2. Easiest way to check this is accelerate to 80km/hr on a straight road with decent revs and then just back off. Watch the duty cycle on the power FC. If it doesn't go to 0% within a few of seconds then that will be a large contributing factor.

3. Minor gasket leaks you might not even hear. I had one that you could barely hear when under the car. Jack the car up on stands and then start the car (make sure its stable) then carefully put your hands round each gasket without touching the exhaust and feel for exhaust escaping. Only guaranteed way I have found to do it.

Edited by nfi
Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558003
Share on other sites

Yes to everything you said.

You're running 25psi and only making 305 rwkw?

Obviously there are many, many factors involved, but as a rough guide, that seems a little low to me.

Even with tiny GT-SS turbos and stock headwork (260 poncams), running 20-21psi, my old GTR made 320awkw (340rwkw?) on CRD dyno (not known for reading stupidly high)

Engine tuners will make an engine run rich to use the fuel to cool down the cylinders and control detonation, at the expense of fuel consumption and reduced power.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558004
Share on other sites

Thanks for that. A small correction, I'm running Garrett 2860 -7s (pretty sure)

Re the cat out the back, that would not surprise me with the amount of kabooms and lighting up the darkness I've had.....Exhaust leak sounds like a biatch to diagnose. I guess the injector thing can be sused by the tuner.

In my experience...

The most common causes of flames I have seen (in order) are:

1. No cat (track days destroy cats.. (I had one blow out the exhaust down the straight a flaming molten lava)

2. Injectors aren't switched off on decel

3. Exhaust leak- because you need oxygen and the engine has used up most of it when it combusted it not as easy for it to ignite and hence only happens at full noise when the car isn't using every last bit of it and the exhaust is red hot. When you have an exhaust leak, on decel the engine goes into vacuum and the exhaust sucks (through the gasket leaks) fresh air.. combine that with a red hot exhaust and you get flames even at partial/mid throttle. (in addition obviously to the fresh air (hot once its gone through the motor) being sucked through the engine on decel).

I would put my money in your case as being likely being a combination of all three. Cats don't last long when you are making big power (1.6 bar +GTSS's suggests to me your making a bit ;-) ) as they just get too hot and I wouldn't be surprised if your injectors are not turning off.

Diagnosis

1. Stick your arm underneath the car and give it a good bash with your fist. If it rattles then its obviously self explanatory, its a dull sound then might be all good and if its sounds empty then that would suggest you no longer have one. Otherwise just take it out yourself its really easy. Alternatively, take it to an exhaust shop. Shouldn't cost much at all for them to take it out and put it back.

2. Easiest way to check this is accelerate to 80km/hr on a straight road with decent revs and then just back off. Watch the duty cycle on the power FC. If it doesn't go to 0% within a few of seconds then that will be a large contributing factor.

3. Minor gasket leaks you might not even hear. I had one that you could barely hear when under the car. Jack the car up on stands and then start the car (make sure its stable) then carefully put your hands round each gasket without touching the exhaust and feel for exhaust escaping. Only guaranteed way I have found to do it.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558019
Share on other sites

Thanks for that. A small correction, I'm running Garrett 2860 -7s (pretty sure)

Re the cat out the back, that would not surprise me with the amount of kabooms and lighting up the darkness I've had.....Exhaust leak sounds like a biatch to diagnose. I guess the injector thing can be sused by the tuner.

No worries.

Exhaust leaks I have a passionate hate for... SR20's sound like tractors enough already without leaks :(

I would check the injectors yourself because the tuner might not even be aware of that feature since its a bit obsecure. He may have left it on to cool the bores but I think its very unnecessary given it compromises response quite heavily as the engine is super rich when you get back on the throttle after backing off and has the potential to actually cause detonation and also wash the bores (of oil) which is really bad. Just literally look at the injector duty cycle and watch the real time readout after backing off. It should go to 0.0%.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558036
Share on other sites

It'll be in the tune Nick - id be surprised if you had a CAT and its flaming... usually a CAT will stop it

Mine rarely flames, Although Snowys car flames a tad more than most for some reason... oh and i dont have the above problem on line one :(

But most GTR's i know about dont shoot flames all that often

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558117
Share on other sites

I used to have flames :( Now I get them only sometimes. That changed with the tune.

While cruising no flames or spluttering but just as I open/close the throttle on cruise i have a little bit of spluttering, its only sound though, you cant feel the car jerking or anything.

Who tuned it?

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558141
Share on other sites

I'd say based on the feedback that I have something that needs attending to, rather than it being 'me' or 'just how they are'. Re the cat, when this was discussed, in context of the whole exhaust that was to be fitted, my tuner was adament I needed one (I was challenging him to go de-cat) due to the potential EPA ramifications. Most if not all my mods are done there and the paper trail would lead straight to him. He said the fines for me are large and for him, larger again and far too large to take a chance on. I'd be 99% sure I have one but what condition it is now in would be my concern.

I'll be checking the tune out I reckon, though that may not be easy for various reasons.......

It'll be in the tune Nick - id be surprised if you had a CAT and its flaming... usually a CAT will stop it

Mine rarely flames, Although Snowys car flames a tad more than most for some reason... oh and i dont have the above problem on line one :D

But most GTR's i know about dont shoot flames all that often

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558293
Share on other sites

i run a 3" decat pipe that has a cat shell welded around the outside of it... we welded it right on the flanges so it looks 100% if you tap it it sounds like a cat and it sure as shit looks like one.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558353
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I will rebutt this and the preceding point from Dose....but without doing any calcs to demonstrate anything and without knowing that I am right or wrong. But... The flow capacity of a fluid transfer system is not limited by the smallest orifice or section of conduit in that system, unless it is drastically smaller than the rest of the system. OK, I use the word drastically perhaps with too much emphasis, but let's drill down on what I really mean. The flow capacity of the system is the result of the sum of the restrictions of the entire system. So, to make an extreme example, if you have a network with 3" pipe everywhere (and let's say a total length of only a few metres) and that 12mm ID restriction of the oil filter connection being the obvious restriction, then for any given amount of pressure available, the vast majority of all the pressure drop in the system is going to occur in the 12mm restriction. But.... increase the length of the 3" pipeline to, say 1000m, and suddenly the pipe pressure loss will likely add up to either be in the same order of magnitude, possibly even exceeding that of the 12mm restriction. Now the 12mm restriction starts to matter less. Translate this to the actual engine, actual oil cooler hose sizing, etc etc, and perhaps: The pressure loss caused by flowing through the narrow section (being the 12mm oil filter port, and perhaps any internal engine oil flow pathways associated with it) is a certain number. The pressure loss through, say, -12 hoses out to the cooler and back is negligible, but The pressure loss through -10 hoses out to the cooler, at the exact same length as the above, starts to become a decent fraction of the loss through the 12mm stuff at the filter port. Maybe even it starts to exceed it. I could actually do these calcs if I knew 1) how much oil was actually flowing in the line, 2) gave enough of a f**k to do things that I hate doing for work, voluntarily for a hypothetical discussion. Anyway - I reiterate. It's not the narrowest port that necessarily determines how much it can all flow. It is the sum. A long enough length of seemingly fat enough pipe can still cause more loss than a semmingly dominant small bore restriction.
    • To pick up what Dose is putting down. Not a lot of point running a huge hose if the motor is still restricted to the smaller size... It's only capable of flowing so much at that point...   *Waits for GTSBoy to come in and bring in the technicalities of length of pipe, and additional restriction from wall friction etc etc*
    • Hooley Dooley these things have some history! If i sell them they will need a certificate of providence to prove they have been in the hands of verified RB20 royalty! They have been stored in a plastic tub, away from sunlight and moisture. They are in mint condition. And they will stay that way, as i have sprung the money for a set of shockworks coilovers. I'm just working on getting them in at the moment, after rebushing the rear of the car, and while the subframe was out i welded in the GKtech reinforcement bracing as well.  They will get a workout at Ararat King of The Hill in November. I ran 48s on the short course there a few months ago, and i am hoping with new bushes and shocks in the rear i can launch a bit harder. There was a fair bit of axle tramp when i tried too hard off the line. a few of the corners had dips mid way which also made the car feel a bit unsettled, hopefully this will help there too.   
    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
×
×
  • Create New...