Jump to content
SAU Community

Recommended Posts

Now i never thought the day would come but......the old girl keeps throwing flames and I'm not sure if it's right as it's happening too often. I think that over time it is getting worse. Symptoms. You do redine gear changes and everything is hot, it blows flames when you lift to change (I'm not unhappy with that). The bit that concerns me is that some mid rpm gear changes it still carries on. Even when it's not blowing flames (big ones) I've had feedback (not from the law TG) that there are little flickering ones visible within the pipe. On a light throttle, tipping in or out, there's a lot of popping and banging going on from the pipe. It all sounds like unstable and incomplete combustion.

Now, I've replace the coilpacks (Splitfire) about 9 months ago and it is making plenty (more than ever actually) of power with no misfire under boost and acell. I run a high flow cat (or at least I've been charged for one), stock dumps and a 3.5" SS system and about 25lb of boost. It's a built engine running forged pistons with about 15k kms on it.

Any qualified people want to give me a steer as to what's happening.

I used to love it and try and make the car do it for my own fun, but now it seems it's happening no matter what....

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/
Share on other sites

Disclaimer: I am NOT qualified to reply to this thread, but I'm waiting for my morning coffee so that I can be productive.

Obviously the root cause if your engine overrunning it's fuel, fuel hitting the red hot exhaust and causing the pretty orange lights.

I assume it's not tuned to run stupidly rich? Your injectors aren't leaking are they? They could be dumping fuel on the exhaust combustion stroke.

The first thing though, is that your cat usually blocks any visible flames, so if you're seeing flames out your exhaust, I'd check that your expensive high flow cat hasn't melted into a molten mess.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557951
Share on other sites

Thanks Andrew. Disclaimer noted. It is tuned to run rich cos it has lots of boost, but stupidly so?.....I'd have to ask the tuner and I doubt he'll say it is stupid. Injectors are new 2 years ago (Tomei 700cc - I think) so I doubt they're leaking.

I'm suspecting it's over-fuelled and possibly ignition retared. If you were an engine builder would you under-fuel and advance ignition under 25lb.....? 305 RWKW isn't that much for my set up considering the boost, so that also leads me to the same thought....

How to check for melted CAT? More to the point, what CATs do not melt? Maybe another question is under what conditions do CATs melt and are there CATs out there that handle tuned GTRs.

More hypotheses please!

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557967
Share on other sites

You're running 25psi and only making 305 rwkw?

Obviously there are many, many factors involved, but as a rough guide, that seems a little low to me.

Even with tiny GT-SS turbos and stock headwork (260 poncams), running 20-21psi, my old GTR made 320awkw (340rwkw?) on CRD dyno (not known for reading stupidly high)

Engine tuners will make an engine run rich to use the fuel to cool down the cylinders and control detonation, at the expense of fuel consumption and reduced power.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4557995
Share on other sites

In my experience...

The most common causes of flames I have seen (in order) are:

1. No cat (track days destroy cats.. (I had one blow out the exhaust down the straight a flaming molten lava)

2. Injectors aren't switched off on decel

3. Exhaust leak- because you need oxygen and the engine has used up most of it when it combusted it not as easy for it to ignite and hence only happens at full noise when the car isn't using every last bit of it and the exhaust is red hot. When you have an exhaust leak, on decel the engine goes into vacuum and the exhaust sucks (through the gasket leaks) fresh air.. combine that with a red hot exhaust and you get flames even at partial/mid throttle. (in addition obviously to the fresh air (hot once its gone through the motor) being sucked through the engine on decel).

I would put my money in your case as being likely being a combination of all three. Cats don't last long when you are making big power (1.6 bar +GTSS's suggests to me your making a bit ;-) ) as they just get too hot and I wouldn't be surprised if your injectors are not turning off.

Diagnosis

1. Stick your arm underneath the car and give it a good bash with your fist. If it rattles then its obviously self explanatory, its a dull sound then might be all good and if its sounds empty then that would suggest you no longer have one. Otherwise just take it out yourself its really easy. Alternatively, take it to an exhaust shop. Shouldn't cost much at all for them to take it out and put it back.

2. Easiest way to check this is accelerate to 80km/hr on a straight road with decent revs and then just back off. Watch the duty cycle on the power FC. If it doesn't go to 0% within a few of seconds then that will be a large contributing factor.

3. Minor gasket leaks you might not even hear. I had one that you could barely hear when under the car. Jack the car up on stands and then start the car (make sure its stable) then carefully put your hands round each gasket without touching the exhaust and feel for exhaust escaping. Only guaranteed way I have found to do it.

Edited by nfi
Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558003
Share on other sites

Yes to everything you said.

You're running 25psi and only making 305 rwkw?

Obviously there are many, many factors involved, but as a rough guide, that seems a little low to me.

Even with tiny GT-SS turbos and stock headwork (260 poncams), running 20-21psi, my old GTR made 320awkw (340rwkw?) on CRD dyno (not known for reading stupidly high)

Engine tuners will make an engine run rich to use the fuel to cool down the cylinders and control detonation, at the expense of fuel consumption and reduced power.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558004
Share on other sites

Thanks for that. A small correction, I'm running Garrett 2860 -7s (pretty sure)

Re the cat out the back, that would not surprise me with the amount of kabooms and lighting up the darkness I've had.....Exhaust leak sounds like a biatch to diagnose. I guess the injector thing can be sused by the tuner.

In my experience...

The most common causes of flames I have seen (in order) are:

1. No cat (track days destroy cats.. (I had one blow out the exhaust down the straight a flaming molten lava)

2. Injectors aren't switched off on decel

3. Exhaust leak- because you need oxygen and the engine has used up most of it when it combusted it not as easy for it to ignite and hence only happens at full noise when the car isn't using every last bit of it and the exhaust is red hot. When you have an exhaust leak, on decel the engine goes into vacuum and the exhaust sucks (through the gasket leaks) fresh air.. combine that with a red hot exhaust and you get flames even at partial/mid throttle. (in addition obviously to the fresh air (hot once its gone through the motor) being sucked through the engine on decel).

I would put my money in your case as being likely being a combination of all three. Cats don't last long when you are making big power (1.6 bar +GTSS's suggests to me your making a bit ;-) ) as they just get too hot and I wouldn't be surprised if your injectors are not turning off.

Diagnosis

1. Stick your arm underneath the car and give it a good bash with your fist. If it rattles then its obviously self explanatory, its a dull sound then might be all good and if its sounds empty then that would suggest you no longer have one. Otherwise just take it out yourself its really easy. Alternatively, take it to an exhaust shop. Shouldn't cost much at all for them to take it out and put it back.

2. Easiest way to check this is accelerate to 80km/hr on a straight road with decent revs and then just back off. Watch the duty cycle on the power FC. If it doesn't go to 0% within a few of seconds then that will be a large contributing factor.

3. Minor gasket leaks you might not even hear. I had one that you could barely hear when under the car. Jack the car up on stands and then start the car (make sure its stable) then carefully put your hands round each gasket without touching the exhaust and feel for exhaust escaping. Only guaranteed way I have found to do it.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558019
Share on other sites

Thanks for that. A small correction, I'm running Garrett 2860 -7s (pretty sure)

Re the cat out the back, that would not surprise me with the amount of kabooms and lighting up the darkness I've had.....Exhaust leak sounds like a biatch to diagnose. I guess the injector thing can be sused by the tuner.

No worries.

Exhaust leaks I have a passionate hate for... SR20's sound like tractors enough already without leaks :(

I would check the injectors yourself because the tuner might not even be aware of that feature since its a bit obsecure. He may have left it on to cool the bores but I think its very unnecessary given it compromises response quite heavily as the engine is super rich when you get back on the throttle after backing off and has the potential to actually cause detonation and also wash the bores (of oil) which is really bad. Just literally look at the injector duty cycle and watch the real time readout after backing off. It should go to 0.0%.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558036
Share on other sites

It'll be in the tune Nick - id be surprised if you had a CAT and its flaming... usually a CAT will stop it

Mine rarely flames, Although Snowys car flames a tad more than most for some reason... oh and i dont have the above problem on line one :(

But most GTR's i know about dont shoot flames all that often

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558117
Share on other sites

I used to have flames :( Now I get them only sometimes. That changed with the tune.

While cruising no flames or spluttering but just as I open/close the throttle on cruise i have a little bit of spluttering, its only sound though, you cant feel the car jerking or anything.

Who tuned it?

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558141
Share on other sites

I'd say based on the feedback that I have something that needs attending to, rather than it being 'me' or 'just how they are'. Re the cat, when this was discussed, in context of the whole exhaust that was to be fitted, my tuner was adament I needed one (I was challenging him to go de-cat) due to the potential EPA ramifications. Most if not all my mods are done there and the paper trail would lead straight to him. He said the fines for me are large and for him, larger again and far too large to take a chance on. I'd be 99% sure I have one but what condition it is now in would be my concern.

I'll be checking the tune out I reckon, though that may not be easy for various reasons.......

It'll be in the tune Nick - id be surprised if you had a CAT and its flaming... usually a CAT will stop it

Mine rarely flames, Although Snowys car flames a tad more than most for some reason... oh and i dont have the above problem on line one :D

But most GTR's i know about dont shoot flames all that often

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558293
Share on other sites

i run a 3" decat pipe that has a cat shell welded around the outside of it... we welded it right on the flanges so it looks 100% if you tap it it sounds like a cat and it sure as shit looks like one.

Link to comment
https://www.sau.com.au/forums/topic/267256-flames-flames/#findComment-4558353
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...