Jump to content
SAU Community

Recommended Posts

Im after expressions of interest for carbon fibre panels in 1,2 and 3 DIN sizes to mount your gauges, rocket switches, turbo timer or boost controller in your air-con control and stereo slots ?

These panels will be made out of high quality SUPER CLEAR epoxy resins and A-grade carbon fibre fabric. Panels will be supplied as blanks so you can cut whatever size holes you like for your gauges or switches etc.....

Just an idea .... I've gotten rid of the ash tray in the centre console in my R33, replaced it with a piece of carbon fibre panel that surrounds the face of my Greddy turbo timer..... nice n neat.

I've also relocated the aircon control to inside the glovebox by extending the wiring harness (TOOK ME AGES !!!), pissed the stereo off (rather listen to the Garrett) and mounted 6x Autometer Cobalt gauges along with 4 rocket launcher switches (fuel pumps, fans, intercooler sprayer etc) and their respective led lights onto a 3-DIN carbon panel..... FULL RACE CAR LOOK....even more so with my Safety21 cage lol

Anyways....

I can also supply carbon fibre fabric / sheets for repairs jobs.....Ive even bonded the stuff to my strut towers in the engine bay to stiffen them up !

I will post up photos of the finished product(s) soon.....watch this space.....

Message or email me if you are interested - [email protected]

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/269120-carbon-fibre-panels/
Share on other sites

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I would like my Tripple gauge, air con vents and air con control unit all in cf to match the gear stick suround in an R34 Gtt.

Would be keen to get these done by you if possible.

Watching.

post-15295-1241929406_thumb.jpg

This is what the material looks like.....genuine carbon fabric.

post-15295-1241930384_thumb.jpg

post-15295-1241930484_thumb.jpg

These are photos of the testing stage,

* Focusing isnt the best as I tried to get close to capture the finish - No bubbles at all due to the type of resin I use. Most people use polyester resins which is thick and therefore traps the air bubbles, this is okay for fibreglass as it's usually painted over. But for carbon fibre, because transparency is required, the clearer the better to capture the lush effects of the carbon fabric. Even most epoxy resins people use is not clear enough for my liking.

The resin I use is water-thin; a special casting resin specially developed for it's extra clear properties. In this application, it is applied in thinner coats which is more time consuming, but it does not trap air bubbles like polyester and by looking at the photos, you will not find anything else that's as clear as this in terms of finish. It's so smooth you can see my reflection off it.

This resin is also UV-resistant therefore it can be used for exterior components as well - Im about to mould a carbon blade for my GTR wing to see how that would turn out.....

Photo of finished product coming soon.

Edited by smok74
I would like my Tripple gauge, air con vents and air con control unit all in cf to match the gear stick suround in an R34 Gtt.

Would be keen to get these done by you if possible.

Watching.

man i'd also like these done too...would look choice as!

im in for these too.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...