Jump to content
SAU Community

Recommended Posts

Hey all, SEI are having a small meet next friday. not many casual meets going on round here so i thought its time for me to organise one. everyone is welcome so bring friends if you want

when: Fri 29th may 8pm

where:

* monash uni car park (multi lvl that you can see from wellington rd)

* then we'll head to spaghetti junction - the intersection of princess hwy, springvale rd and center/police rd. the place is just up the service lane from the kfc.

* we can decide from there if we are gonna cruise or not. if we do, i have a route in mind that'll do.

monash.jpg

Link to comment
https://www.sau.com.au/forums/topic/271259-sei-kebab-run/
Share on other sites

  • Replies 340
  • Created
  • Last Reply

Top Posters In This Topic

what is sei? i might be in for this one

South East Imports. A club for all import drivers, rather than a particular type of car :P Mind you, it's 90% SAU members anyway.

www.southeastimports.net

Edited by jezza boii
Link to comment
https://www.sau.com.au/forums/topic/271259-sei-kebab-run/#findComment-4611034
Share on other sites

Ok, so far...

Confirmed:

Basti - black R33

(OO)SKYLINE(OO) - gunmetal R32

krzysiu - orange R33

jezza boii - black MR2

lil_lucky - black R32

eMsta - R33

Maybes:

RBPOWA - white Stagea

Edited by jezza boii
Link to comment
https://www.sau.com.au/forums/topic/271259-sei-kebab-run/#findComment-4612369
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...