Jump to content
SAU Community

Recommended Posts

Euro mate said both the Toerag and the Howdy were good tow cars, his opinion on maintenance etc is based on his own experience, he runs a euro workshop in Sydeney. I asked him about the little VW diesel SUV, whatever it's called, for towing but it's too light. And probably too fragile.

Have driven a Santa Fe, not bad if you don't mind the FWD bias. My searching for 'what tow car' is over, will post once the buy is done :)

Fathom said his was a water pump failure. Apparently ALL of them required replacement, but VAG gambled. Rather than issueing a recall that was unmanagable, they elected to instead replace the pumps when the vehicles were seen for service. Fathom's was one that failed prior to be replaced.

So, given that was a couple of years ago, one would assume all the pumps have been done by now.

Mitsubishi Challenger SUV, 2.5 turbo diesel, five speed sequential shift auto, 2WD, three tonne towing capacity :yes: Only thing is with the auto torque is reduced from 400nm to 350, no LSD but I assume that the electronics sort that out. Everything else looks good, these would be the cheapest diesel SUV with a serious towing capacity around, by a big margin.

Mitsubishi Challenger SUV, 2.5 turbo diesel, five speed sequential shift auto

Make sure you take it for a test drive - on a flat 100 - 110k road.

A guy here at work has the Triton version (diesel + auto) and it has a massive surge problem where it refuses to sit on 110... on a dead flat road, without moving your foot (or in cruise) it will hunt between 105 and 115. It has been back to Mitsubishi dozens of times over the last 2 years where they have swapped everything imaginable, including re-flashing the ECU with a custom program from MMC Japan... and then replacing it when they bricked it on one attempt.

I think he is basically now at the stage where he has given up on it and is just waiting till it is due to be replaced.

Apparently there was something strange about his combo from memory though, he appeared to get the motor from one series coupled to the GBox from a different series or something along those lines - not that it is actually changing gears when it happens.

Edited by samstain

The diesel Land Cruisers are not bullet proof despite what the Toyboys may like to think. Talking with a bloke out at Lakeside the other day, he bought one new and at 140K the fuel system dropped it's guts, had to be towed. Cost $7K to have it rebuilt. 650nm would make one a monster tow car though.

Mitsubishi Challenger SUV, 2.5 turbo diesel, five speed sequential shift auto, 2WD, three tonne towing capacity :yes: Only thing is with the auto torque is reduced from 400nm to 350, no LSD but I assume that the electronics sort that out. Everything else looks good, these would be the cheapest diesel SUV with a serious towing capacity around, by a big margin.

Interesting, had a look at the nt model pajero as well which looking at car sales is a slightly dearer price for an 09model about 30k

f**k just replaced the rubber on the q7

Nothing but the best china high load shit

780 fitted foR 4 tires. 275/45/20's

f**k yea

When did rubbeR get so cheap?

Cheap cheap!

I was surprised at how cheap you could get them too, especially for such a ridiculous size. I can get Yokies for under a grand. Crazy!

Make sure you take it for a test drive - on a flat 100 - 110k road.

A guy here at work has the Triton version (diesel + auto) and it has a massive surge problem where it refuses to sit on 110... on a dead flat road, without moving your foot (or in cruise) it will hunt between 105 and 115. It has been back to Mitsubishi dozens of times over the last 2 years where they have swapped everything imaginable, including re-flashing the ECU with a custom program from MMC Japan... and then replacing it when they bricked it on one attempt.

I think he is basically now at the stage where he has given up on it and is just waiting till it is due to be replaced.

Apparently there was something strange about his combo from memory though, he appeared to get the motor from one series coupled to the GBox from a different series or something along those lines - not that it is actually changing gears when it happens.

Does it happen to have a snorkel fitted?

I like your thinking, but no I don't think so... it is all very stock - just dealer fitted times such as a canopy and bull bar of some description from memory.

It would be interesting to see where the air intake for the stock air box is. I've seen certain 4WDs have them in a wheel arch, which caused pressure issues at speed.

Might be worth having said person investigate and see what happens if a snorkel is fitted (Or an air intake from somewhere else)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...