Jump to content
SAU Community

Recommended Posts

Might be worth investigating what another one is worth, if they are cheap then add in the power and see how it goes. If they are a fortune a cooler might be a good option, also have a chat with some of the 4wd shops for what they are doing with them.

Blokes on a Challenger forum have driven their bone stock autos loaded up and towing caravans around Australia with no problems so I reckon mine should be OK on tarmac roads towing 2000kg all up max. But an auto trans temp gauge might be good, will check that out. Don't want to add stuff that is apparently not necessary, spare $ go to racecar :)

So cbf reading bucket load of pages!

X trails....say 09 on wards diesel.

I've noticed that the autos are 1350kg towing and manuals are 2000kg towing. What's reason behind that? And I guess towing the mx5 and trailer, would it be that hard on the manual?

Seen a few around 20k to 22k which don't seem too bad.

So cbf reading bucket load of pages!

X trails....say 09 on wards diesel.

I've noticed that the autos are 1350kg towing and manuals are 2000kg towing. What's reason behind that? And I guess towing the mx5 and trailer, would it be that hard on the manual?

Seen a few around 20k to 22k which don't seem too bad.

Reduced towing for the auto usually is because the auto is the transmission weak link. Torque is what matters with a diesel, I'd say 300nm minimum for your application.

Xtrails won't be happy towing - they'r all kinds of shyte.

If it's a very light car on a very light trailer (say total 1300-1400kg) you might get away with it. If you're considerint towing up to 2 tonne then forget it. Xtrails only just make the cut as a family car. They're not designed to tow.

So cbf reading bucket load of pages!

X trails....say 09 on wards diesel.

I've noticed that the autos are 1350kg towing and manuals are 2000kg towing. What's reason behind that? And I guess towing the mx5 and trailer, would it be that hard on the manual?

Seen a few around 20k to 22k which don't seem too bad.

Chris,

This might help you, is the petrol versions I think so deisel would be better

http://caravanersforum.com/viewtopic.php?f=2&t=4842

New Jeep Cherokee on special offer, $30k for the four speed auto V6 petrol (diesel with five speed auto is an option) drive away, 2270kg towing capacity. http://www.jeep.com....cherokee-towing

Edited by 260DET

$30 k is cheap for a base model which (I think) is being run out. It's a nice car and would do the job if you're towing something light like an mx5 and light weight trailer.

For example, my Jeep Grand is rated to tow 3.5 tonne, but I personally can't imagine towing that kind of load. I tow a 33 gtst with a 750kg trailer and various bits and pieces. I reckon around 2.5 ish tonne is my personal limit, giving a bit of overhead or buffer.

Pretty sure it was suggested there may be some other options some pages back?

Again - the Cherokee still very cheap! Wonder if you can get stock?

  • 2 weeks later...

personally i wouldnt touch a jeep, the missus wants a wrangler and i am spewing, terrible fuel economy, parts are expensive and depreciation is one of the worst on the market.

it depends though, if you only drive her once or twice a month and you dont care about fuel consumption get a 100s v8 land cruiser

$20k should get you a nice one

my cousin has been towing his 1800kg boat in his ls1 wh statesman for years and it purrs along the freeway

$5-10,000

07 v6 hilux dual cab sr

15-20.000

id take a hilux anyday of the week over a navara, triton, colorado or mazda for that matter

even a v6 territory you can have for around the 10-13k mark for a decent one

but def no jeep

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...