Jump to content
SAU Community

Recommended Posts

I dont think I can get more than 400km on a full tank in my M35 - I have only filled it twice since I got it, but it is chewing a hell of a lot more than my C34 stagea which was modified - My M35 is 100% stock!

Maybe I need a tune...

  • Replies 112
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just filled my tank for the first time, I never fill it but now I'm commuting :(

67.22L of 98 Vortex and the screen is telling me 545km @ 8.1KM/L.

Now I just have to control my right foot :D

The M35 should only use about 9.5-10L/100 on the highway. Anything over 10L/100km (or under 10km/L) on the highway means either something is not right or your right foot is heavy/shaky. Make sure to put the tiptronic into 5th when sitting on constant speed because otherwise the throttle is too sensitive and the torque converter will keep locking / unlocking, which will end up using more fuel. For some reason using the tiptronic makes it less sensitive and will keep the revs low and constant. :laugh:

The above is for a completely stock stagea. Depending on which performance mods you have it may do better / worse...

In my own experience, mine averaged 10.5-11L/100km on the highway when in D. Putting it in 5th using the gear lever gave me 9.8L/100km but I've seen lower than that since. I'll be doing another long interstate trip in about 5 weeks and reckon I should be able to beat 9.5L/100km this time.

Edited by pixel8r

WWATTTT ? 8.1 damn thats pretty high

did u just reset?

I reset a couple of days ago as I've been doing a lot of f3 driving and wanted to see how driving on the f3 was using mostly automatic mode, just slipping into manual shift for overtaking etc.

I'm hoping to be more like 10+km/L once the ECU is remapped.

Note that the M35 holds 10 more litres of fuel compared to older stageas, so 400km on a tank in a M35 is worse than 400km on a tank in a s1 or s2.

I'd say 430-500km would be a more accurate average for the M35, although it does vary quite a lot depending on where you live/drive etc.

I thought I would revive an old thread :down:

I done my regular commute from Blacktown to Tuggerah today and reset all the major efficiency and timing devices on the screen.

Here are the stats for my trip:

post-59561-1247833364_thumb.jpg

post-59561-1247833416_thumb.jpg

GAS ETA, i like it! :P

But atleast I've posted up some stats, will be interesting to see my stats after the remap in it's current configuration.

It should be putting out more power and using less fuel, can't go wrong!! :P

Once we know the remapping works and is beneficial it will be time to get a turbo to GCG for a high-flow rebuild and supply the new turbo with the dump pipe to Envy Imports for change over.

I'm excited, I've also asked Envy Imports for a quotation to supply and fit a FMIC with 3" plumbing.

The ECU should arrive from Brisbane about Tuesday, I should have paid the extra and had it sent from Japan early last week lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...