Jump to content
SAU Community

LED Parkers

Henros

By Henros,
in General Automotive Discussion

 Share

Recommended Posts

Henros Enthusiast

Henros

Posted
  • Author
Posted

Hey guys,

Thanks for the replies. They're not off the shelf replacements, I made them myself. Each "bulb" is made up of six 5mm white LEDs, in 2 strings of 3. I added a dropping resistor (68 ohm) for current limiting and a diode (IN4004) for reverse polarity and transient high voltage protection. The whole package was soldered onto a very small PCB and plugged into the original socket. The only downside is that LEDs have a much narrower light cone, so that the light doesn't look as spread out as the original bulb, but the colour is a lot nicer.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-576420
Share on other sites
sewid Grand Master

sewid

Posted
Posted
Originally posted by Henros

Hey guys,

Thanks for the replies. They're not off the shelf replacements, I made them myself. Each "bulb" is made up of six 5mm white LEDs, in 2 strings of 3. I added a dropping resistor (68 ohm) for current limiting and a diode (IN4004) for reverse polarity and transient high voltage protection. The whole package was soldered onto a very small PCB and plugged into the original socket. The only downside is that LEDs have a much narrower light cone, so that the light doesn't look as spread out as the original bulb, but the colour is a lot nicer.

Cheers.

To diffuse the light output of 5mm LED's you can sand down the "lens" portion of the top of the LED.

Try it out and see if it improves the light spread.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-576571
Share on other sites
Henros Enthusiast

Henros

Posted
  • Author
Posted

Here it goes guys, my first step by step guide

1. Remove the parkers from the car by disconnecting the wiring and twisting the sockets anticlockwise 90 degrees. This step is sure to be accompanied by much swearing the cutting yourself due to the awkward position and lack of clearance. Persistence is the key and may the force be with you.

2. Remove the 5W wedge lamp and measure the diameter of the socket opening (round end). I can't remeber the exact measurement but it should be around 13 to 14 mm. Cut either a blank PCB (printed circuit board) or a prototype strip board into a circle with the same diameter. You need 2 of those. The PCB approach is neater but needs etching to produce the pattern. The prototype board has pre-existing copper tracks but you're gonna have to work out the wiring pattern according to the circuit diagram yourself, but that shoudn't be hard. You can even use an insulating material without and copper tracks and just solder the component legs directly to each other. The role of the circular board, whatever you decide to use, is to provide a physical and electrical mounting platform for the electronic components. I will describe the PCB approach here.

3. The circuit diagram is given below (see LEDParkerCircuit.gif). As you can see, the LEDs are connected in a series-parallel configuration to minimise electrical dissipation. The resistor provides current limiting and the diode provides protection against reverse polarity and transient high voltages. I have used a resistor value which will drive the LEDs at 20 mA when the engine is on (13.8V). If you want to increase the brightness, you can reduce the value a bit, but I wouldn't go any lower than 51 ohms (which is 30 mA at 13.8V).

4. The PCB pattern was designed according to the circuit diagram, see diagram (LEDParkerPCB.jpg). Replicate the pattern with a permanent marker and let dry. Once dry, the PCB can be etched in either a iron III chloride or ammonium persulphate solution. The solutions are made by desolving appropriate amounts of the chemical powder in water. Read the instructions accompanying the chemicals. The ammonium persulphate solution need to be warm to work, so use hot water.

5. After etching, rinse the PCB in fresh water and clean off the permanent marker with metho or mineral turps. Rinse in water again. Drill holes in the PCB as shown in the diagram below (LEDParkerPCBDrilled.jpg).

6. Insert LEDs onto the board from the non-copper side and solder in place as shown in the diagram (LEDParkerPCBLayout.jpg). The resistor and diode are solder only at one end on the copper side. They also fuction as electrical contacts. See

diagram (LEDParkerPCBSoldered.jpg). Note that I have used 2 resistor in parallel, that's because I didn't have any 68 ohm resistors at the time.

7. Bend the leg on the other side of the resistor and diode and apply liberal amounts of solder to they fit snuggly in the socket contacts.

8. Plug the LED module into the socket and test it on the car. If the LEDs do not light up, reverse the pins and try again. Once you'll satisfied, secure the PCB to the top of the socket with a little bit of superglue. This is to make sure that it doesn't get shaken loose by vibrations. The finished product is shown in LEDParkerAssembly.jpg

9. Reinstall the parkers and wiring. Enjoy your new blueish white parkers!

Disclaimer: I take no responsiblity for anything that happens to you or your car should you give this a try.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/27452-led-parkers/#findComment-577362
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...