Jump to content
SAU Community

Removing Harmonic Balancer On R32 Gtr

phat25t

By phat25t,
in General Maintenance

 Share

Recommended Posts

phat25t Community Regular

phat25t

Posted
Posted

Hey I'm trying to remove the nut in the centre of the harmonic balancer with a power bar, I just want to make sure it needs to be turned anticlockwise because I know I've removed one on another car that was backwards(it needed to be turned clockwise to loosen.

Cheers ,

Steve

32_Dave Mentor

32_Dave

Posted
Posted
yep its a normal bolt. letft loosy, righty tighty.

could be vft though

they are VVVFFT (very very very f**king f**king tight) if its never been out before.

believe its 140-150 ft pound 14-15kg

get a steel pipe on the end of your breaker bar. if u got a flywheel lock use that or if your ghetto put a bolt in the block where the box would bolt up and pivot off it using a screwdriver slotted into the flywheel teeth. both methods work :D

cheers

Duncan Grand Master

Duncan

Posted
Posted
they are VVVFFT (very very very f**king f**king tight) if its never been out before.

believe its 140-150 ft pound ....

even worse on gtr, 400lb/ft. for some reason gtst is only 150 odd.

br3ndan Mentor

br3ndan

Posted
Posted

A good way of doing this is...

position ur breaker bar so its leaning on the ground put the key in the iginition and turn her over. The car will un do it for you.

Only attempt this if you are confident...im sure they didnt need to be said tho.

turbo_brian Community Regular

turbo_brian

Posted
Posted (edited)

http://www.enginebuildermag.com/Content/Si...00000006981.jpg

Use the right tools and to it properly.

You can get a hammer-tool and socket, place socket onto bolt, hammer-tool into socket (dont know it's actualy name or I would have put up a picture, but it's got an arm about 10cm long, then another arm from this about 80cm long, you hammer the longer arm and it shock-loads the bolt right at the thread).

Or you use a tool like in the picture above, where it holds the harmonic balancer from turning, and the 2nd arm is used against the harmonic balancer's locked pressure to turn the nut (uses SFA energy to crack the thread).

Reason you dont place the car in gear, or use a fly-wheel lock is because your then placing all your force down the length of the crank shaft, and if your hitting the bolt, using a rattle gun, etc your placing shock-loads onto the crank and potentially damaging the crank.

Reason you dont use the starter is for the same reason.

Dont get me wrong, these methods work, but they place un-due force on the internals of the motor, and 'could' cause potential failure points in the future.

EDIT: Almost forgot, USE FLAT FACED SOCKETS!!!! Dont use the milling grip sockets, you will almost certainly round the nut, and then be stuffed!!!

Edited by turbo_brian
  • 1 month later...
Jmaac Proficient

Jmaac

Posted
Posted (edited)

You can remove the starter and use a screwdriver to lock the flywheel before using a breaker bar. I still couldnt loosen it first time, but you may be able to. This worked after I loosed everything up using the method below.

I ended up using an electric impact gun. It removed it easily and effortlessley. I tried the first procedure for 2 days and started to go mental over the one bolt holding me up. Use a proper impact bit and it'll absorb all those nasty 'shock loads' (crank can handle it no probs anyway).

Use a proper fitting socket (full hex/flat face) as mentioned

Also as above bush mechanic style, you can use a breaker bar on the bolt and brace it against up against the chassis and crank the motor over with your starter. I would recommend against this though as the starter will give way before the crank

Edited by Jmaac
Duncan Grand Master

Duncan

Posted
Posted
I bought a breaker bar and smashed it as hard as I could but no go, not sure what to do with it now?

you get a longer breaker bar!

easiest way to do that is put a long jack handle / pole of some sort over the breaker bar. Once you get to 1-2m long you will have enough leverage to undo it

Rowdyr32 Mentor

Rowdyr32

Posted
Posted
you get a longer breaker bar!

easiest way to do that is put a long jack handle / pole of some sort over the breaker bar. Once you get to 1-2m long you will have enough leverage to undo it

I've had a couple where I have had to put a bicycle innner tube around the balancer and then a chain from the balancer to the front tow hook and then wrap a racket strap bloody tight around the inner tube and chain. This is the only way I could get two engines bolts to crack with a 3/4 drive breaker bar and a pole with two people.

There was to much flex in the drive train and couldn't get it to stay still any other way. It would just turn with the purchase. Some are bloody tight!

  • 1 month later...
phat25t Community Regular

phat25t

Posted
  • Author
Posted

Hey guys,

I still have not been able to get this off due to time and this thing being f%$king tight. How did you guys fit an impact gun in the engine bay?? I have the radiator out but theres not enough room to get my air impact gun behind the pulley.

Cheers,

Steve

Beer Baron Grand Master

Beer Baron

Posted
Posted

sadly having it done up too tight it still far better than the ones that are not done up tight enough and come undone!!! d'oh! happens a lot and is sometimes an easy fix and sometimes will cost you an engine.

R324DR Proficient

R324DR

Posted
Posted

with the right leverage you can undo most things. i had to put my car up on a hoist, attach a very long steel bar to the breaker bar, get underneath the car, and get two people to swing off it. not the most professional way of doing it, but it worked.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Chris' Toyota Mark ii JZX110

      By PranK · Posted

      This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • soviet_merlin
      Duncan's V37.......race car?

      By soviet_merlin · Posted

      Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • Murray_Calavera
      Jacks that fit under GTR lips that can reach the subframe?

      By Murray_Calavera · Posted

      My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Duncan
      Chris' Toyota Mark ii JZX110

      By Duncan · Posted

      Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
×
×
  • Create New...