Jump to content
SAU Community

Recommended Posts

Hi guys

I'm considering abt keep or get rid of my NISOM wing on my R34 GTT. The car is black and the wing is the real set from jap came with the car, which means it cost a lot!!! Around $800 for the real 3 piece set in Jap!!!

I have pics here, so what u guys think? Back to standard one? Or keep it?

Looks like this, but all in black.

post-52244-1248271048_thumb.jpg

post-52244-1248271523.jpg

Link to comment
https://www.sau.com.au/forums/topic/280325-nismo-wing-on-r34-gtt/
Share on other sites

It's quite a task to remove the factory aero wing, i believe theres about 8 bolts (2 on each rear quarter panel and 4 in the bootlid) So unless you completly can't stand it, i'd carefully consider

I remember one guy on here, said he paid up to 2K to remove the wing, weld the holes and respray the 3 panels, so it's a costly project unless you want rust coming through

Most people on here hate that wing but i love it haha, it looks nice if you got a big bodykit to go with it

All the best

Danny

Mmmm gotta say dude, in my opinion its yuck. Worst spoiler ever made. May be expensive, but i would pay someone to take it away for me.

I say take it off, sell it, you could get some money for it.

Each to their own of course though

It's quite a task to remove the factory aero wing, i believe theres about 8 bolts (2 on each rear quarter panel and 4 in the bootlid) So unless you completly can't stand it, i'd carefully consider

I remember one guy on here, said he paid up to 2K to remove the wing, weld the holes and respray the 3 panels, so it's a costly project unless you want rust coming through

Most people on here hate that wing but i love it haha, it looks nice if you got a big bodykit to go with it

All the best

Danny

Looks like u and me are the only two in the world who like it dude, are u going to buy them? Caz everyone ask me to get rid of it~ I'll make it cheeeeeeaaaaaaaap for u.

It's quite a task to remove the factory aero wing, i believe theres about 8 bolts (2 on each rear quarter panel and 4 in the bootlid) So unless you completly can't stand it, i'd carefully consider

try 7 on each quarter panel and 2 on the bootlid

no joke

dude get rid of it

its way too big a it destroys the rear look of the car.

i had it on mine and its the best thing i ever done

unfortunately there are 6 bolt holes on each guard for those ugly side pieces, so even if you change to a stock/gtr wing you will need someone to patch it up..

cost me $1350. all holes led filled was $350 and undercoated(a friend of a friend done it) could cost upto $700.

and i got the rear reprayed for $1000.

check my gallery pics you'll see the difference.

Why? Sorry man I didnt get it?

I was commenting on the other guys post,

sorry I'll be more constructive for you

in my opinion it's a big undertaking to remove the nismo spoiler and should only be done properly, no shortcuts.

There will a total of 7 bolt holes on each rear quarter which will need to be patched up, if you are going for the wingless look the 4 bolt holes on the boot will have to be filled in as well, if you want to add a spoiler than don't worry

that still leaves the 14 bolt holes which will need to be patched up for the rear quarters.

welding plates behind and bogging the holes will be cheaper but rust can still happen and the rear quarters can warp if a rush job is done so paying the little bit extra for a proper job will be better for the long run (ie; the panel shop should solder the holes up, not weld plates in and bog, blend paint from the roof back etc so it was as if the car never left the factory with that ghastly spoiler)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...