Jump to content
SAU Community

Fast & Furious Skyline Stolen From Hollywood Garage


Recommended Posts

Found this funny, though I'd share

Fast & Furious Skyline stolen from Hollywood garage May 17th 2009 at 1:44PM

paul_walker_nissan_gt-r.jpg

It took two years to build it in reality, ten seconds of montage to put it together on screen, and about ten minutes to steal it. In a rare automotive example of life imitating art imitating life, the Nissan Skyline that Paul Walker drove in the latest Fast & Furious movie was stolen from its storage facility in Los Angeles.

Although dressed up to look like a full-on R34 GT-R for the movie, the car underneath was actually a lower-spec GT-S. Reports indicate that thieves, evidently knowing the car was inside, broke through a metal door and ripped off that specific car, leaving the rest but sideswiping a Studebaker and a Porsche Boxster on the way out. And to make matters worse, the car, valued at around $75,000, wasn't even insured. Considering the movie grossed $72.5 million in opening-weekend box office sales alone, we doubt the seventy-five grand will be terribly missed.

Original http://www.autoblog.com/2009/05/17/i-fast-...llywood-garage/

GT-S ??? is that what we call the GT-T but n/a equiv ER34

i the movie its clear and obvious BNR34 dash cluster with 4wd and a-lsd lights in fail mode

so its an ER34 rear wheel drive with BNR34 kit for action shots etc, but interior is BNR34 with left hand drive and hacked 4wd and a-lsd

i just cant understant how it was woth $75,000? and i remember seeing the movie on the big screen and hated every second of it just wanted to slap the director in the face with my .....

and how dumb would you feel stealing a fake gtr haha

Yea the obvious reason why they are so cheap and popular here is because japan and australia drive on the same side when I lived in NY an R33 GTST would prob cost about $25g's US unconverted

75k USD for a R34 GT-T modded to look like an R34 GTR. Why don't you just friggin buy an R34 GTR? Seriously... I can't imagine a secondhand R34 GTR costing more than a Viper (approx 75k), including say 10-20k for a LHD conversion.

if doggy look alike r34 gtr's are worth $75k us dolla might start exporting them by the boat load lol

just watch the movie you can tell there not to bright lol maybe thats why paul and vin didnt make it to aus because they realized where not that stupid over here down under.

Damn it would make it easier if all cars were RHD and all units in metric. UK, Japan, Australia, India, SE Asia all drive on the correct side. Doesn't it make sense to do the most skill-requiring procedure (steering) with your dominant hand and the less skill-requiring ones (shifting, turning up the music, eating, touching girls) with the non-dominant hand?

It's the USA's fault. If they go RHD, the rest of the undeveloped world will follow. Then, hey, great savings for auto makers and consumers everywhere in the world. :)

world's most expensive GT (seeing as there's no such thing as an R34 GTS).

Lol, yeah, just realised in the pic as well that it's an unconverted RHD R34 GT. Sh!t that skyline exporting business is looking mighty attractive right now Travis :)

Damn it would make it easier if all cars were RHD and all units in metric. UK, Japan, Australia, India, SE Asia all drive on the correct side. Doesn't it make sense to do the most skill-requiring procedure (steering) with your dominant hand and the less skill-requiring ones (shifting, turning up the music, eating, touching girls) with the non-dominant hand?

It's the USA's fault. If they go RHD, the rest of the undeveloped world will follow. Then, hey, great savings for auto makers and consumers everywhere in the world. :angry:

Someone has their priorities in order.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
    • Not sure yet.  Was considering speedtek because it was rated to 800hp, but when I did some research about him I don't think I will go for that🤣 So maybe giken gear set, but I'm afraid it won't be strong enough🙄
×
×
  • Create New...