Jump to content
SAU Community

Recommended Posts

Can anyone give me a 100% definitive answer on what the situation is with a defect in Victoria in a QLD registered car and a QLD licensed driver?

Both VIC roads and QLD transport are “cagey” to say the least in just what happens. I assume there is some form of national data base? However, again both VIC and QLD cannot confirm nor deny – VIC roads cannot even check a QLD license status unless they were to call QLD transport I'm told?

I assume one would take the VIC ticket and either pay in VIC? (VIC calls QLD so points come off QLD license??) or pay in QLD and they call VIC etc?

Bit lost as to what actually happens.

Thanks

Can anyone give me a 100% definitive answer on what the situation is with a defect in Victoria in a QLD registered car and a QLD licensed driver?

Both VIC roads and QLD transport are “cagey” to say the least in just what happens. I assume there is some form of national data base? However, again both VIC and QLD cannot confirm nor deny – VIC roads cannot even check a QLD license status unless they were to call QLD transport I'm told?

I assume one would take the VIC ticket and either pay in VIC? (VIC calls QLD so points come off QLD license??) or pay in QLD and they call VIC etc?

Bit lost as to what actually happens.

Thanks

Did you get booked as well as defected ?

If you have been booked well you will need to pay that. No question

But as for the defect i would not stress that much. Coz what maybe a defect here in vic may not be a defect interstate.

Rip ya sticker of and dont get pulled over till ya go home.

I know with licensing and fines/speeding etc all you do is pay the fine itself and the points do not get carried over to your respective state.

Id imagine any fines for anything else to be the same, however the defect itself IMO would be like the points - no carried over so no drama's

As per what others have said, if you got a driving infringement it needs to be paid. However if you have a QLD car it cannot be defected by a victorian police officer. Thanks to Australias system where each state has its own rules in regard to car mods (I'm NOT talking about ADR's here) a vic police officer cannot defect a QLD car and vice versa. Therefore the defect should be null and void.

The only bit that may get you into trouble is if you have moved to vic from Qld....by law you are required to change your drivers licence and car rego after 3 months. If they find out you are living here with a qld rego'd car you will be in trouble.

Do not use this advice as gospel and chase it up with the police.

I know with licensing and fines/speeding etc all you do is pay the fine itself and the points do not get carried over to your respective state.

if the fine he received has points attached to it, the points will be transferred from vic to qld.

the defect however is invalid once your over the border.

demerit points are transferred between states. Unfortunately I have a driving record to prove it.

but, for those that want the low down. heres the link to qld transport..

http://www.transport.qld.gov.au/Home/Licen...demerit_points/

Licence demerit points

If you commit a demerit points offence anywhere in Australia, the demerit points allocated for the offence may be recorded on your traffic history.

Your traffic history is a record of all of your road rules related offences, as well as any drink-driving, drug-driving, dangerous driving or vehicle registration offences which you have committed in Australia.

The demerit points set for the offence are taken to have been allocated on the day that you committed the offence, as soon as you have either:

paid the fine set for the offence

or

been dealt with by a court for the offence.

i have had a friend get pulled over and got a warning defect of $130 per defect. so they dont defect you but give you a fine and warning per defectable item, his car was just to low so it was a easy $130

SA rego and driving in VIC

Living in QLD on a VIC licence and VIC rego I can tell you first hand that the points do not get deducted off my VIC licence and they can not defect my car. They have told me this when i got pulled over for speeding and on another occasion for "making exsissive noise" both of which are 3 point penalties in QLD. They said the systems are not linked. Im sure if I was doing something totally stupid they would call up and ask for the points to be deducted.

All monetary penalties must be paid. I do think the VIC and NSW systems are linked.

Living in QLD on a VIC licence and VIC rego I can tell you first hand that the points do not get deducted off my VIC licence and they can not defect my car. They have told me this when i got pulled over for speeding and on another occasion for "making exsissive noise" both of which are 3 point penalties in QLD. They said the systems are not linked. Im sure if I was doing something totally stupid they would call up and ask for the points to be deducted.

All monetary penalties must be paid. I do think the VIC and NSW systems are linked.

Not being a smart arse but why wouldnt they be linked around all territories and states. What this is saying is that an interstate driver can come to vic and get busted doing 120kmh in a 100 zone all day long with only a fine to pay on each offence (20kms over being not that harsh off an offence. I find this hard to beleive. Surely points would have to be deducted!!

Not being a smart arse but why wouldnt they be linked around all territories and states. What this is saying is that an interstate driver can come to vic and get busted doing 120kmh in a 100 zone all day long with only a fine to pay on each offence (20kms over being not that harsh off an offence. I find this hard to beleive. Surely points would have to be deducted!!

Yes, but I'm sure repeat offenders would be treated differently to the once-off offender.

And its probably on a per state basis, for example Victoria may not take care of the transfer of points if you get fined in QLD or something, old legacy government systems that are probably not linked together.

I'm sure if you got caught multiple times in a particular timeframe there might be an issue there :(

"What this is saying is that an interstate driver can come to vic and get busted doing 120kmh in a 100 zone all day long with only a fine to pay on each offence"

http://www.vicroads.vic.gov.au/NR/rdonlyre...ndfines0910.pdf

View the costings. You get enough demerit points to spare... cash is harder to come by.

Edited by abacusnow
http://www.vicroads.vic.gov.au/NR/rdonlyre...ndfines0910.pdf

View the costings. You get enough demerit points to spare... cash is harder to come by.

Yes this is true but wouldnt it be easier to hide from teh vic gvment for not paying a fine in S.A or QLD if they wernt linked then what it would be if they were???. Think of how many people dont pay speeding fines???

Not being a smart arse but why wouldnt they be linked around all territories and states. What this is saying is that an interstate driver can come to vic and get busted doing 120kmh in a 100 zone all day long with only a fine to pay on each offence (20kms over being not that harsh off an offence. I find this hard to beleive. Surely points would have to be deducted!!

It was more the point to provide information to the contrary that was earlier posted.

It was more the point to provide information to the contrary that was earlier posted.

ok then

1. A vic police officer can do a licence check on a qld licence ( i rem this from when i used to listen to my scanner)so YES they would be able to see how many points you have left. I dont know about vicroads themselves if they can check it for you.

2. I may be wrong here cos i havent had a fine in a while but dont you pay a fine via bpay or at a post office?? That way it wouldnt matter where you pay the fine, it would still go to the vic gvment coffers.

3. I may be wrong again but a defect notice remains in the state of where that defect took place. As in your case it happened in vic, which means your car is still roadworthy in other states, just not vic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...