Jump to content
SAU Community

Recommended Posts

Just got the prices for servicing from Von Bibra yesterday

10000km - $600

20000Km - $600

30000Km - $2500

Pre and Post race day

Pre race day - $450

this includes

1. Wheel alignment

2. Download of computer information

3. Engine oil level reduction

4. Brake fluid level reduction and bleeding of system

5. Power steering fluid level reduction

6. Aluminum tape over wheel weights

Post race day - $600

1. Wheel alignment

2. Brake fluid changed

3. Download of computer informaiton

4. Top up of power steering fluid

5. Removal of wheel weight protection tape

?? Transmission oil change (cost not covered)

?? brake rotors and pads change (cost not covered)

I wonder whether they mind me taking my RX7 for the GTR trackday instead :blink:

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/
Share on other sites

Considering the 10K service is an oil and filter change with a few "inspections" seems a bit steep to me even when we're not talking trans fluid change...... Would love to know what they charge for oil. I used to supply my own oil to the Subaru service dept, save money and still get a better oil than what they would have been providing.

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4758600
Share on other sites

Pre track inspection is not mandatory. For the post

track day inspection, about $370 is for flushing brake fluid. Bugger that. Surely they can't enforce that for engine transmission warranty. That leaves $220 for hooking it up to the computer and poking around under the car. That's what I'll argue for.

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4765099
Share on other sites

Pre track inspection is not mandatory. For the post

track day inspection, about $370 is for flushing brake fluid. Bugger that. Surely they can't enforce that for engine transmission warranty. That leaves $220 for hooking it up to the computer and poking around under the car. That's what I'll argue for.

I thought both pre and post track inspeciton are compulsory?

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4768433
Share on other sites

Pre and Post race day

Pre race day - $450

this includes

1. Wheel alignment

2. Download of computer information

3. Engine oil level reduction

4. Brake fluid level reduction and bleeding of system

5. Power steering fluid level reduction

6. Aluminum tape over wheel weights

:huh:

Umm, why are they REDUCING the important fluids in your car before a track day? That just seems a bit silly to me...

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4768958
Share on other sites

:huh:

Umm, why are they REDUCING the important fluids in your car before a track day? That just seems a bit silly to me...

Weight saving strategy? ha ha

There is probably some method behind the madness. But i would put i in the same bucket as nitrogen filled tyres. Basically a wank for casual weekend warrior stuff.

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4769151
Share on other sites

:)

Umm, why are they REDUCING the important fluids in your car before a track day? That just seems a bit silly to me...

Engine fluid is reduced to decrease oil pressure, as when racing the oil temperature rises and the increased oil pressure could potentially burst pipes

:blush:

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4770309
Share on other sites

Engine fluid is reduced to decrease oil pressure, as when racing the oil temperature rises and the increased oil pressure could potentially burst pipes

:)

I would have thought increased oil temp would reduce viscosity and therefore reduce oil pressure. Oil pressure is usually managed by a regulator/bypass system when oil is cold and by engine clearances when engine is hot.... Also how would reducing the oil level reduce oil pressure short of reducing it so far the oil pickup doesnt "pick up". Which I hazard would create a catastrophic reduction in oil pressure. My only concern with reducing the oil level is the risk of oil surge under hard braking/cornering. However I cannot imagine running the car at the H level will create excessive windage that will aerate the oil. I imagine the Nissan engineers looked after that with good sump baffling etc. I'd always erron the side of more full than more empty...I'm sure Martin could shed some light on this topic...

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4770722
Share on other sites

Lol do they ever top the oil back up or do they just take more and more out every track day you go to until your engine siezes? Its so stupid that they can get away charging rediculous prices for the exact same stuff that is done to any car for a lot less. I have been servicing my car for quite a few years now and it costs me 1/3 that of what most places want to do simple tasks. Here is a question, do JRM R35's get no support in aus? Like if you need any factory work done will they refuse your car because it was imported?

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4772091
Share on other sites

Lol do they ever top the oil back up or do they just take more and more out every track day you go to until your engine siezes? Its so stupid that they can get away charging rediculous prices for the exact same stuff that is done to any car for a lot less. I have been servicing my car for quite a few years now and it costs me 1/3 that of what most places want to do simple tasks. Here is a question, do JRM R35's get no support in aus? Like if you need any factory work done will they refuse your car because it was imported?

that's where the post-inspection comes in ..... open up the oil filler cap, pour in the oil and voila $600 please ...... i think both Moorooka and GC dealer says they dont deal with JDM cars, but i maybe if ur willing to pay more? money talks

Link to comment
https://www.sau.com.au/forums/topic/282658-servicing-fees/#findComment-4773191
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...