Jump to content
SAU Community

Recommended Posts

  • Replies 158
  • Created
  • Last Reply

Top Posters In This Topic

Sounds like this is a common thing with plugs ins.

The computer needs a throttle signal as an input to decide what to do with the diff.

The A-LSD computer probably expects a signal to come to it in a particular way, and if it doesn't come in the correct form, then it faults.

So how should we fix the signal? I've had a mechanic check the wires, and he didn't see any issues... :(

OFENSV - yeah...mine doesn't come on when i first turn on the car...and it goes away if the car is turned off for awhile! The a-lsd light on the dash is not the one that flashes a signal. The flashing signal is on the a-lsd/abs computer in the boot. Don't know how to describe it, but it sits above the battery...you have to lean into the boot and look at the bottom of the computer...there will be a little round light that flashes out a sequence. (mine flashed 7 times slowly, then 5 times fast, indicating a tps prob - i think you need to ask someone what the different sequences mean : )

I definitely think its linked in with the pfc, cause i never had that problem with my stock ecu....

  • 3 months later...

Just chanced to happen on this thread when surfing the forum.

Hope you gels got your problems sorted. I could barely understand much of the discussion. I only bought my car in May 2004, so am still on steep learning curve.

Mine is also an R33 active LSD model, built Feb 1994. I managed to track down an owners handbook in english. Its been helpful for the basics.

It says both activeLSD and slip lights (ABS light as well) come on with the ignition, but go out when engine is started. Slip light also comes on when losing rear traction (eg having fun in the wet, or doughies, or perhaps on ice/snow in Japan). Active LSD light (and ABS light) only comes on when driving if there is a system fault.

My car (now) does it exactly like in the manual. But mine is stock standard. Mucking around with electronic mods seems too scary too me.

Hope this is helpful to some active LSD owners.

cheers :(

Hey I don't have an Active LSD 33 but going back to your original qu Moanie I'm pretty sure that the PowerFC doesn't support the Active LSD - hence the lights coming on when the PowerFC is installed..

Nah. I've recently had a powerfc installed and I don't have any problems with it. My slip light and A-LSD/ABS lights are working fine. Not that I have tested them of course. :angel:

I seem to find that it creates a system fault when you are driving up an uneven driveway and one wheel spins but the other is off the ground? Or on a dyno. It comes up with a system fault. Not quite sure why, but my mechanic said it's fine :rofl:

Moanie/NismoGirl. A Q. if I may? Whats a power fc, or shouldn't I ask?

I used to have an FC holden (1959) in a former incarnation, but you wouldn't call that powerful - by today's standards. And I'm sure it's not the answer to my Q.

Hope you are making progress with problems. I have no further insights, beyond how the lights are supposed to work.

Initially, mine did have a problem. None of the ABS,slip, or active LSD lights ever came on. Under warranty, so dealer had problem for 3 weeks. Turned out it was a broken wire inside a plug somewhere. It was like these systems had been turned off with a switch.

Interesting that both ABS and slip/activeLSD systems both ran thru one wire. Seems to support earlier post that both these systems are run from the one computer??

Gazza49: Before you get flamed for your nOOb question. A PowerFC is a full stand-alone replacement ECU which plugs in where your normal Nissan ECU is which allows you to modify your fuel/ignition maps as well as a few other features, like rev limiter etc.

Obviously if you replace the standard ECU which is supposedly running all these bits and pieces like A-LSD etc, you come up with problems if the new computer (ECU) can't handle it.

You'll notice in my signature that i'm awaiting a PowerFC and this certainly doesn't mean i've got an FC holden on order :)

I've search around, checked all 490 odd pages of the r33 service manual and other sites and google. The diff is the same as the vpec gtr diff. If the problem doesn't occur when you use the stock ecu and it does with the powerfc then it must be something the power fc is doing. Not sure what. The service manaul for the r33 doesnt cover anything on the a-lsd or slip functions, it doesnt even mention them

nissan consult wont prove much help either it doesnt have any a-lsd loopback or realtime tests. Find someone else who has a a-lsd r33 and see if you can swap your "lsd" computer in the boot over as a test, but if that was the problem then youd have the same fault with your stock ecu

no idea

I totally agree!!! With all the trouble shooting we did, that had to be the only explanation!! and i haven't noticed any probs with my lsd.... so i'm trying not to stress too much!! I have an awesome mechanic and tuner... so if there was a problem, they'd have already found it by now!! :mad:

Thanks for everyones input!!!! Its always good to hear it coming from someone else :)

Gazza49: Before you get flamed for your nOOb question. A PowerFC is a full stand-alone replacement ECU which plugs in where your normal Nissan ECU is which allows you to modify your fuel/ignition maps as well as a few other features, like rev limiter etc.

Obviously if you replace the standard ECU which is supposedly running all these bits and pieces like A-LSD etc, you come up with problems if the new computer (ECU) can't handle it.

You'll notice in my signature that i'm awaiting a PowerFC and this certainly doesn't mean i've got an FC holden on order :mad:

What's a nOOb question? But ta for reply anyway.

The FC holden wasn't that bad when I think about it. Mine had a Repco super sports engine (but still a sideplate grey), twin carbs, extractors, 2 inch exhaust, fats (steel wheels), lowered suspension and a top speed of 84 MPH. My mates called it the ROCKET.

Is it to late to change your order?

  • 3 weeks later...

Hi Moanie

I have a series 2 with the slip/a-lsd option on my car also.

i was looking in to getting a PFC, and i did actually pose this question on the forums, as i did think about whether apexi would have thought of adding this option in to the PFC, since only few GTST's came with it (maybe the new model PFC have it???).

the responses i got was that the PFC DIDNT come with the inbuilt function to handle our diff (vspec GTR diff). i didnt end up getting PFC though, as im selling my car now, but if i did, i would have imagined i would of got the same 'problem' as you.

if the diff actually still works though, then you dont have much to worry about..

-Michael

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That was the first session so not a lot to take from the day. It was low 20s ambient and the coolant had got to 110 (and obviously had some pressure!) so that still needs to be addressed. I haven't downloaded the data yet but will. I had refilled the auto trans with Redline DT6 because it claimed the best viscosity I could find at 100o. It wasn't really long enough to get a good feel for that; while the trans got to 100o in the session it still wasn't shifting crisply as I hoped. I think I'll try a few more sessions before judging. No steering motor overheat but I'd hope not in only 1 session! But finally the suspension; it was night and day over the standard stuff and the car was a couple of seconds quicker on the same crappy tyres, which is a huge difference. I'll stick with that and get some sway bars and a mechanical diff sorted too and see how that all goes together
    • I guess it’s partially a compromise of how my car is used, wanting to be able to switch from drift to grip with track side on-car adjustment. Also partially with the way the knuckles are set there is more static camber but less dynamic camber gain. 
    • OK, so update from the track day on Friday It was a classic "an unfortunate series of events'. There were a few cars around and when i checked my mirror coming out of the fish hook I notice some smoke from the rear of mine. Looked again and it was getting much worse, I figured I'd blown a turbo or something to got off it and pulled off the racing line. However.... since it is a left hairpin into a right kink, I was on the inside of the next corner. There was a car passing me on the left and a big drop off over the ripple strip on the right......and someone had knocked the witch's hat that was on the apex about 1m onto the track. So, between those 3, I decided to mow down the cone and not damage my car/the other car. Right choice, but surprising result.  The car decided the cone was a small pedestrian so it blew the rear bonnet hinges up to protect their head in the upcoming person to car impact....I didn't see that coming and like an airbag deployment it happened super fast. Straight into the pits from there, everything was driving fine but it became clear it was a coolant leak not smoke, it was billowing up onto the windscreen. Onto the trailer and home. I'll do a separate thread about the repair (once I work out what it is ), but the immediate problem was the bonnet wouldn't open because the front was pinched onto the front bar and would not release. Ultimately we unbolted the hinge from the bonnet, pulled it back a little and it released from the front OK. "There's your problem", the top radiator hose had popped off at the radiator.
    • Yeah that looks like great caster, but I'd suggest trying less front camber some time and seeing if it helps with braking without reducing mid corner speed too much
    • I ended up setting the rear 5mm higher than normal to give some clearance.  My plan is to run the least camber I can in the rear which I think with the extra width is going to need to be -1.75 to -2.00° just to get clearance.  Guards have been rolled and pulled as much as they can/I would be wanting to.  front has the Acostal knuckle with the KPI change and the drop etc. So should be okay with the existing settings I have run with AR1s etc Front: Toe total -2mm(1mm out each side) Caster +7.5° Camber -3.8° Ackerman +15°
×
×
  • Create New...