Jump to content
SAU Community

Recommended Posts

I have just taken delivery with this http://www.skylinesaustralia.com/forums/Eo...ts-t285533.html

The RB25 has Arias forged pistons, Arp head studs and new bearings etc, gcg highflow and is roughly 2200kms old now. Now when cold it has a very slight chatter which I've been led to believe is completely normal for forged pistons, as this is due to the increased clearance between the cylinder wall and the piston.

Now the first few minutes if I accidentally get it on boost (1-2psi not much) it will blow a very small amount of blue oil smoke, as the pistons have not yet warmed up and theres still a gap I assume this is relatively normal? It currently has 15-50w mineral oil in it but I am planning on putting some fully synthetic 5w-40 in it soon. It only blows the smoke once, after this and once it is warm it runs beautifully and doesn't chatter or blow smoke. This should be nothing to worry about providing I warm the motor up before boosting it yes? The idle is also slightly rough, not as if it is missing just more like it has a cam (which I'm quite sure it doesn't).

Now with mantaining a forged motor, what are some things I should do to make sure I look after it. Does it require longer to warm up than a standard motor? and is synthetic 5w-40 quality oil (mobil, elf, motul etc) acceptable to use in it providing I change it every 5000kms. The car is a daily driven car and will see occasional track action and I just want to know if there is anything I should be doing differently than I would with a standard motor.

Oh also it currently has a run in tune with a rev limit of 6k and is running about 12psi making ~220kw as it now has 2200kms on the clock would it be safe to take it in for a full power tune with 18psi and a 7.5k rev limit? It has all the appropriate fueling to handle the gcg highflow turbo

Cheers everybody.

Edited by Rolls
  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Do you know how the previous owner ran the engine in?

Shouldnt be blowing smoke at all if the rings have bed in. All of the rebuilt engines ive seen have never blown smoke.

Could have a very small oil leak in the turbo and oil that you see is it burning off.

But if its noisey when cold it the clearances might be a little too much. Nothing serious unless it breathes under load/RPM.

Did the previous owner build the motor? Does he have engine specs/measurements?

Was built by sabbadin automotive in Victoria, they did all the work. The previous owner drove it very sedately for around 1600kms from what he told me, he seemed like a very honest bloke so I have no reason to doubt him. One the drive home vic-> sa we did about 700kms and we varied the driving a lot, cruising at 4k, a few 4th gear runs to 6k and varied the load around town.

It really is hardly any smoke at all and will only blow it once maybe twice, after that it is fine. If you start it warm it doesn't blow anything either. It definitely doesn't breathe under load when driving and is very smooth/quiet once warm as well so that was my conclusion, that the clearances were slightly too large.

I might ring up sabbadin tomorrow and request all the specs of the rebuilt just for my own knowledge.

The previous owner drove it very sedately for around 1600kms from what he told me

need to find out if it was run in properly. from what i've read driving sedately isnt the right way to run an engine in

need to find out if it was run in properly. from what i've read driving sedately isnt the right way to run an engine in

I guess it wasn't run in optimally then, I've been giving it a fair bit of hell, varying loads etc since I've got it so is this the best way to do it?

The RB25 has Arias forged pistons, Arp head studs and new bearings etc, gcg highflow and is roughly 2200kms old now. Now when cold it has a very slight chatter which I've been led to believe is completely normal for forged pistons, as this is due to the increased clearance between the cylinder wall and the piston.

A nice tight built forged motor should not have chatter in today's day and age, none of my built motors have EVER made a noise.

However it is normal for some forged motors to use a tiny bit of oil in between servicing, and by a little i don't mean 500ml's, maybe 100 or so (if you measure how much you put in/take out etc).

For it to be blowing a bit of smoke etc when cold points to one of two things in my book.

1. Not the tightest motor ever built

2. Rings not bed correctly

Now, given you are hearing noise on cold startup, it is likely to be #1.

However this does not mean #2 is ruled out :P

Need to drive it hard and put it under plenty of load straight away. Easy driving wont help bed the rings in.

Yep ;)

And doing it 2,200km's later isn't going to fix the problem either.

Bed/seating the rings etc is critical and needs to be done in the first 20mins of engine starting for the first time.

Now with mantaining a forged motor, what are some things I should do to make sure I look after it. Does it require longer to warm up than a standard motor? and is synthetic 5w-40 quality oil (mobil, elf, motul etc) acceptable to use in it providing I change it every 5000kms. The car is a daily driven car and will see occasional track action and I just want to know if there is anything I should be doing differently than I would with a standard motor.

Oh also it currently has a run in tune with a rev limit of 6k and is running about 12psi making ~220kw as it now has 2200kms on the clock would it be safe to take it in for a full power tune with 18psi and a 7.5k rev limit? It has all the appropriate fueling to handle the gcg highflow turbo

Cheers everybody.

Simply start it up, ensure you have oil pressure and drive it lightly/easily for the first 10mins. No boost etc.

Do not go by when the water temp gauge is reading hot. You have motor/gearbox/diff oil etc etc to get warm as well :banana:

That is what i do, and so far it has not failed me.

Especially considering it sounds like it was a loose build, limit getting onto boost at all in the first 10mins.

As for what oil etc - totally depends on what the builder recommends to be honest.

My motors have all been under strict instruction of Castrol Edge 10/60, change every 5,000kms.

And yes - wind up the boost, get some power running into it. It should have had a full tune in the first 500km's IMO. But every builder has 'their ways'.

Some are older than others, ie older motors did require a bit more of a run in, tolerances were not as tight, things not as good in terms of quality... however things change over the years :)

Hope that helps.

Are you Vic?

A nice tight built forged motor should not have chatter in today's day and age, none of my built motors have EVER made a noise.

Are you Vic?

Cheers nismoid, when I say chatter I mean very very minimal chatter, if you weren't trying to listen for it you wouldn't hear it and as soon as it is warm it sounds like a stock motor. Motor is amazingly responsive and torquey so even if it isn't the tighest motor ever its f**king amazing compared to my 20 year old rb20det I had :P

As far as the full tune I believe it has had a proper tune, just only at 12psi and a bit richer, when the seller (builder told him this) said full tune he meant bump it up to 18psi and sure it is running well at this. What is roughly the maximum psi the GcG highflow should be running on a rb25, I'm assuming they don't release a compressor map for this turbo? When I get it tuned for whatever the maximum flow this turbo can handle, what sort of rev limit should I be getting set, 7k? 7.5k? I will ask the tuner but be interesting to know what you guys think, the gears are way too short with the 6k rev limit at the moment and it seems to really start pulling at 6 so I'd think it would make good power all the way to 7.5k

With warming up my procedure is to start the motor, wait 30 seconds for oil pressure to come up and circulating then drive off very slowly, revs around 2.5k with absolutely minimal load for about 5 minutes.

Sounds like all is good, I will do a service on it tomorrow with some good quality fully synthetic oil, probably elf or motul depending on what is available.

There is a small leak coming from the front of the engine as well, maybe 6-8 drops over night can be seen the next morning, I've had a looked at it seems to be coming from the front of the sump. What seals could these be, cam seal, is there a front main seal ?? or anything else that could leak? Going to pull the CAS and timing cover off this weekend and figure out what seal it is, then replace it hopefully.

Oh and no I am in SA, I did buy the car from VIC however.

Edited by Rolls

Since giving the motor hell on the drive back and the last few days it barely blows any smoke at all, few wiffs at startup if you accidentally boost it.

Should I dump the mineral oil now and put this Mobil 1 0w-40 fully synthetic oil I got for free off my mate? Or should I leave the run in oil in a bit longer? It is going in for full power tune on 18psi on Wednesday the 7th.

Edited by Rolls

Personally I think it's difficult to put a Km number on when to dump the first lot of oil , I reckon 1000 Km is a little high if you've run it in properly .

Putting around like grandma simply doesn't work because without some engine load you don't get high enough combustion pressure behind the compression rings to push them out against the cylinder walls while they have that rough honed finish .

Really having a turbo engine means you can achieve higher cylinder pressures so its easier to bed the rings in with a bit of boost .

I can't for the life of me work out why people think ahh ya can't run it on boost and must drive to Perth and back on 2% throttle and it's essential to have a tail wind . I just finished running in my dinosaur Subaru EA82T engine and it doesn't blow any smoke ever or use any oil - at all .

It was actually a less than perfect situation because the builder put Elf semi synthetic 10W50 oil in it and I didn't realise this for a couple of days .

Myself and a mechanic friend spent time loading this thing up (WOT and the full 6 lb farts worth of std boost) between 2500 and 4500 revs and I did my best to drive it up the longest steepest hills I could find at WOT .

At 800 k's I changed the oil to Mobil 1 Racing 4T 15W50 which is bike oil and it runs fine .

People absolutely have to understand that newly honed cylinder walls have rough peaks and they are intended to "wear" or bed the compression rings in . If you putt the thing around and waste those sharp peaks the rings may never bed in and seal properly . The only way to rectify that sitiation is re hone the bores and start again .

As for the oil I think a lot of the warm up urban myths come from using yester years honey like dino oils ie 20W50 . A good synthetic pours cold like water by comparison so its got to get around the engine faster at start up and lubricate properly to begin with . I'm not suggesting that people flog cold engines but if you had to I think a good synthetic would be kinder to the engine .

Your calls , cheers A .

Well said. Whenever we purchase a new truck isuzu tells us to load the back to maximum weight and flog the shit out of it. Can sit on full boost for a minute straight pulling up big inclines. They never use any oil. We also have another truck of same model year we got as an ex demo and it needs 500ml a week easily as it was pansied around as a demo.

Also seen a mates 500rwkw+ motor run in on the dyno for maybe 20 minutes maximum. Drain oil, refill with good stuff and full power tune.

If rings are not bed by over 2000km then its basically too late.

Been flogging it since I got it and it barely blows a wiff now.The oil level on the dipstip hasn't moved either back 1000kms ago when it was blowing a bit of smoke.

Edited by Rolls

Just got off the phone from the engine builder (rob sabbadin from sabbadin automotive) and he said the clearances are 3thou so there should be zero smoke even when cold. I've since looked in the catch can (basically empty) and pulled the intake piping off and it is full of oil, now theres no possible sources of oil apart from the turbo, the other possibility is leaking valve stem seals but the owner spent $900 on getting the head reconditioned.

He talked to me a lot about the motor and was very adamant that it was built with tight tollerances and was certainly not a sloppy build. He however suggested that the motor still needs to be run on mineral oil to make sure that it runs in properly, even after 2200kms which I am a bit dubious about, said the mobil 0w-40 oil I have will be too thin and that I should use a 15w-40 fully synth.

However I'm thinking it is most likely that a seal in the brand new gcg turbo that is leaking? Any idea which one and how hard it would be to fix?

The turbo is only 2200kms old so I'm sure it is under warranty, I just don't fancy removing it and sending it interstate.

Edited by Rolls

Mineral 2200km's into a build doesn't make sense to me to be honest.

None of my motors have had mineral in them for longer than the dyno runs - if at all (i vaguely remember someone telling me it was full synth from the first turn)

but he is the builder - do what he says

Mineral 2200km's into a build doesn't make sense to me to be honest.

None of my motors have had mineral in them for longer than the dyno runs - if at all (i vaguely remember someone telling me it was full synth from the first turn)

but he is the builder - do what he says

they only say these things to cover their own arse... not because its the right thing to do or not.

in the few motors ive rebuilt and had rebuilt, ive loaded them up from the word go, run mineral oil for the first 1000 kms and then straight to synthetic oil.

its not a complex process, yet some people/builders believe that a motor is still running in some 2000 km later... no its not.

(i vaguely remember someone telling me it was full synth from the first turn)

Benno told me its synth from the first turn... when I picked mine up, I waited til oil got up to temp and then gave it a hammering (as per instructions) :cool:

one of my old 25 builds (not from Ben) I babied for ages and it was never right... had piston slap when cold and never got any better... only lasted 25K before I destroyed it

The phone was crackling at the end and he said it was a high soap engine and that will wash the bores so to use mineral. I assume he meant the oil (fully synth) was high soap content? I am going to do as he says and leave the mineral oil in there until it gets dyno tuned anyway.

So yeah re the turbo smoke issue what do you guys think? I will be sending GCG an email tonight and see what they have to say.

Edited by Rolls
i had a turbo rebuilt by *** about two years ago and started leaking after about 500 kms ide be looking at the turbo

Did they cover it under warranty? and if so how long was the turn around from taking it off to putting it back on?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...