Jump to content
SAU Community

So Ive Taken Off My Rb20 Turbo...

IM-32-FK

By IM-32-FK,
in Engines & Forced Induction

 Share

Recommended Posts

IM-32-FK Mentor

IM-32-FK

Posted
Posted (edited)

So ive taken off my stock rb20 turbo from my 32 gtst. Ive transfered the actuator from the rb20 to the rb25(higher psi - 10) but ive got a question....Whats this "nipple piercing" thing ive reading about. Im completely lost ATM. By the way, im using this guide:

http://www.project32.net/tutorials.php

as quoted from that webpage:

Nipple You may have noticed, the rb20 turbo has the nipple for the wastegate line direct to the compressor housing. Turbo reaches XX psi, wastegate opens, gasses pass into exhaust.

The rb25 doesn't, and relies on you t'ing the wastegate up to the outlet, preferably as close as possible to the turbo outlet itself. Depending on your piping setup, you may have a nipple in your piping simply blocked off � easy, don't have to do anything. If not, you'll have to tap into your piping a standard nipple.

You'll need to drill the piping, and then get the nipple (these can be purchased from supercheap or repco for a few bucks), welded in there, or if you can thread your piping, you can screw it in tight. Just make sure there is no leak, and that it can't pop off under boost.

Here you can see the nipple I have screwed into my existing piping. Done.

he also gives a pic:

turbonipple.jpg

If someone can explain to me, in a more general sense, what EXACTLY i have to do? what does welding a "nipple" onto the intercooler piping do? This "nipple"...what kind of bolt is it?

ill be forever grateful for your help :down:

Edited by IM-32-FK
Link to comment
https://www.sau.com.au/forums/topic/291924-so-ive-taken-off-my-rb20-turbo/
Share on other sites
Granthem Mentor

Granthem

Posted
Posted

The nipple allows you to hook a pip from the nipple into your wastegate, allowing it to open the gate once the pressure is enough to open it.

Without running this line to your wastegate, the turbo will essentially free boost, and destroy itself (and possibly your motor) in no time.

I suggest you go into supercheap, explain you want a brass nipple vacuum fitting to screw into your intercooler piping. You shouldnt have too much trouble being pointed in the right direction.

IM-32-FK Mentor

IM-32-FK

Posted
  • Author
Posted

Ive got a boost tap where one pipe runs to the actuator and the other runs into the actual turbo when i had my stock rb20 turbo in there....would i still need to put the nipple onto the piping?

diagrams would be helpful.

BANGN Experienced

BANGN

Posted
Posted (edited)

best thing is to buy a brass fitting to suit vac hose that has thread on one end.. drill a hole cooler pipe closest to the outlet of the turbo and wind the fitting on with a spanner and get someone to silversolder/weld it so its sealed. you can get brass fittings from most auto shops (veals)

Edited by BANGN
IM-32-FK Mentor

IM-32-FK

Posted
  • Author
Posted (edited)
I just unscrewed the nipple from the 32 turbo and drilled and tapped the compressor housing on the 33 turbo to suit. The 33 housing still has the stand-off for the nipple only it's not drilled...

are you talking about this?

http://img235.imageshack.us/img235/9563/dyaln025.jpg

thats the rb20 turbo. The rb25 turbo has that same part but the hole has no threads or anything. Can i just take that part off the rb20 turbo and put it on the rb25 turbo?(if yes, do i drill it and tap it?) After ive done that, do i get another nipple any put it on the end of the hose and then weld it onto my intercooler pipe just before it connects with the crossover J pipe? or do i put the other end on the crossover pipe?

Edited by IM-32-FK
Chris-06R Community Regular

Chris-06R

Posted
Posted
I just unscrewed the nipple from the 32 turbo and drilled and tapped the compressor housing on the 33 turbo to suit. The 33 housing still has the stand-off for the nipple only it's not drilled...

Thats exactly what I did too... just make sure you get as much of the swarf (metal shavings) out as you can.

On your pic you can actually see the blank where you can drill the hole out, tap it, and then put in the fitting that was on the rb20 turbo. All the hoses should go back onto the same places that they came off on the rb20 turbo, so forget about drilling/welding/tapping into your crossover pipe.

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

theres 1 nipple/port on the actuator. all you have to do is make sure that nipple sees boost when the motor sees boost. if you dont want to tap a fitting just buy a little T piece and T into one of the vac lines off the intake manifold, preferably not the fuel reg line.

IM-32-FK Mentor

IM-32-FK

Posted
  • Author
Posted
Thats exactly what I did too... just make sure you get as much of the swarf (metal shavings) out as you can.

On your pic you can actually see the blank where you can drill the hole out, tap it, and then put in the fitting that was on the rb20 turbo. All the hoses should go back onto the same places that they came off on the rb20 turbo, so forget about drilling/welding/tapping into your crossover pipe.

thats not what the guy at skylines spares told me. I was told to just connect the actuator hose to the intercooler piping with a nipple on both ends...

StealthX Veteran

StealthX

Posted
Posted
Without running this line to your wastegate, the turbo will essentially free boost, and destroy itself (and possibly your motor) in no time.

off topic and just out of curiosity, which do ya think would happen first in the situation?

blown motor or turbo?

i got money on turbo, if were talking about stock ceramic ones.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • perry_r33
      R34 GTR Vspec Garage Sale - All must go!

      By perry_r33 · Posted

      Pm sent 
    • Robot
      Skyline v36 350GT sedan hunting on idle

      By Robot · Posted

      Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...