Jump to content
SAU Community

Recommended Posts

]']i was in my SKY white R32 GTR  

with plates JDM-32R

i was in the traffic in the opposite lane and u were in the non conjesting direction :)

Sometime before last weekend, were you going through the roadworks towards Castle Hill at the start of Castle Hill Road (Thompsons Corner) at about 2:00AM?

you know, WRX.

crappy, fwd, understeering thing

Im not sure, I might have got the brand wrong, was it a daewoo? kia?

hehehe!!!

yes i also spotted A-HUGE-xxx on the Anzac bridge, top down, wind in the hair - i think i may have even spotted you running your hand through your hair and glancing in the rear view mirror admiring yourself duncan! is that true?!? :wassup:

that wrx was the WRP10. priced halfway between a wrx and an sti, it has sti springs, sti ecu, sti wheels, sti front strut brace and lots of badges! it went really well. most impressed and more importantly heaps depressed that it reminded me of what a performance car was like to drive! :blast:

round 2:30 was driving near a maroon r33 plate was BENTY on penno rd

then about 3pm behind a r32 GTR gunmetal and no wing on kingsgrove rd

and while on kingrove rd i think i spotted Tommy K filling up at the shell servo

or another black R33 GTR

round 2:30 was driving near a maroon r33 plate was BENTY on penno rd

then about 3pm behind a r32 GTR gunmetal and no wing on kingsgrove rd

and while on kingrove rd i think i spotted Tommy K filling up at the shell servo

or another black R33 GTR

Benty works here @ ibm, he's parked near me before.

megeer silver 33 on pennant hills rd... boundary rd... new line rd... towards dural last night 9ish

white 33 with a huge rear wing turning right on to new line from castle hill rd this arvo at about 6:30

silver 33 on shepherds drive 6:30ish this arvo... even got a thumbs up :)

I spotted a white R33 series 2 parked on Coonara Avenue as I left the IBM carpark. It was parked, had the drivers window down (white number plates, can't remember plate).

That was me parked outside my mates place. :)

Saw a black GTR pull out of IBM as I left. GTR-**X

Sometime before last weekend, were you going through the roadworks towards Castle Hill at the start of Castle Hill Road (Thompsons Corner) at about 2:00AM?

um..yeap that would have been after my lil run with the curcuit club boyz through OP

where u driving oppostie direction from me?

should have waved :D

]']um..yeap that would have been after my lil run with the curcuit club boyz through OP

where u driving oppostie direction from me?

should have waved :D

I was about 2 cars behind you - this was before I got my R33 so I was driving the family Camry!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...