Jump to content
SAU Community

Recommended Posts

Spotted Mr Ed32 Doing His Run To Palmy Going Through Avalon....Luky You Were Taking Advantage Of Non - Double Demerits, A High-Way Patrol Car And Undercover Ford Just Behind YouOn Your Way Back FromPalmy....Car Looked The Goods!!!

you had the xennons? very nice looking car mate. i wanted a black one but none were for sale at the time......

i was giving my mates a rest after a spirited drive through church point, they were watching some music dvds and were entrawled in them :laugh:

I was being so carefull though, i saw sooooo many cops in the area!

Very sensible- NOT

I'm sure the cops wouldn't have minded spotting you, double demerits or not.

/Kel stops speaking like your mumma now :)

its ok... i was driving sensibly untill after midnight :) nah it was more of a chill and chat drive than anything moronic, and with the number of cops that we saw i wasnt going to take any risks.... but ill take your advice...Mum :P

Spotted myself.. paid $1.49 a L tonight at the servo :<

how does mona get spotted weeks after her car is off the rd and yet I never get spotted :laugh:

He he he :) Cos i came flying around the corner nearly hit her car then realised............. she was waiting for Mansoor........... blocking an entire lane

Mr Ed32 - No, you wouldnt of seenmy car,it was parked at the time, but was good to see your car around....Have seenplentyof skylines around palmy lately, keep them comming SAU!

Was that you again tonight Mr Ed32,around 10.30 close to a r33 maroon and blue sti?

flashed lights at a silver R32 gtr yesterday afternoon near my parents house..

plates were AWD-15T (I think).

he waved and I waved back.

Pull over at my parents place like 50 meters ahead of when we waved.

next thing I know he's done a U turn and stopped next to me, looks at me then drives a little further past and does a U turn.

as he drives away he goes all read faced and goes sorry I thought you were someone else..

hahahaha

He thought I flashed and waved cause I knew him but it was only to say HI to a skyline owner..

LOL.

how does mona get spotted weeks after her car is off the rd and yet I never get spotted :D

spotted slim at space station last night!! hi!! :laugh:

today:

spotted some old bitch in a 323 Astina ABF93F rolling into me at a set of traffic lights

also spotted various other random people.. i waved at them, but damn camry/falcon drivers never wave... just look at me wierd n stuff

spotted a dark blue 33 GTST series 2 on Newline Road this morning. It had powerplay stickers on the rear quater windows.

I waved while the guy stared :D... I was the white car with the cf bonnet on purchase rd waiting to turn right.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
×
×
  • Create New...