Jump to content
SAU Community

Recommended Posts

Spotted Ferrari 430 in chatwood but the little dead end lane......some bald guy was driving it and tried to impress the ladies by revving it on his way out. Sadly all he got was a couple of disgusted head shakes, no one was impressed

ok just spotted a dude in a blue r34 GTR with green p plates, on hume highway, the was also a wrx they dragged and i sat back and watched not far behind, wen i decided to give it a hit the gtr turned off :laugh:

but by the looks of it, the wrx kept up with him :D

so i raced the rexy and um hate to say it, i left him for dead :D

also spotted a pulsar sss, with an sr20det in it, man that thing went hard, gave him a run also and only managed to pull away slowly in 4th gear :( it had some grunt!!!

Edited by mass_iv
spotted a white r34 gtr GTR PWR had a lil run with him on silverwater rd

HOLY F*$&%EN SHIT!!! He actually took it out and drove it!!! hahahaha

Spotted Mass just then trying to look hektik in his Skyline on Victoria Rd :P

HOLY F*$&%EN SHIT!!! He actually took it out and drove it!!! hahahaha

Spotted Mass just then trying to look hektik in his Skyline on Victoria Rd :(

hahaha sif trying look hektik :( I AM HEKTIK ;)

Spotted me and mass outside the shop in rushcutters tonight....

i was eating some of that fffffffffarken awesome gelato he has to offer! Highly Recommended!!!!!!!!!!!!

hehehe yep that gelato has attracted some of the whores already in the past :ban:

ah the good old gelato runs.....

now on another note, i just got pulled over on my way home from work :ban:

i was speeding over that dam old anzac bridge, i copped a $590 fine and am going to lose my licence again for 3 months :ban: this is just not my month!!! stupid 60 zone, shud be 80 :P

now on another note, i just got pulled over on my way home from work :(

i was speeding over that dam old anzac bridge, i copped a $590 fine and am going to lose my licence again for 3 months :( this is just not my month!!! stupid 60 zone, shud be 80 :P

ghey

Spotted me and mass outside the shop in rushcutters tonight....

i was eating some of that fffffffffarken awesome gelato he has to offer! Highly Recommended!!!!!!!!!!!!

thats MY gelato!!! :D

hahaha sif trying look hektik :O I AM HEKTIK :pirate:

hehehe yep that gelato has attracted some of the whores already in the past :pirate:

ah the good old gelato runs.....

now on another note, i just got pulled over on my way home from work :rofl:

i was speeding over that dam old anzac bridge, i copped a $590 fine and am going to lose my licence again for 3 months :( this is just not my month!!! stupid 60 zone, shud be 80 :thumbsup:

oh -MASS- :(

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...