Jump to content
SAU Community

Recommended Posts

spotted Blitz I think i was - 4 door 32 with 33 gtr rims?

couldnt see the plates this time, but tooted and yelled out again!

oh, was in Linfield, similar time & place to where I spotted him a while ago!

spotted a rex went off road next to north parra maccas, chick was drivin, think she was racin a ute or something...

lol completely off..

i was there that night too..

This guy in a blue ute ran a red light and hit her side on.. she locked up and slid onto the gutter missing the jaycar wall by about 30cm.. lucky shewas alright just some cuts on the side of her face, blood everywhere..

where were you? i was in a 32 there..

WRX plates were BRATZ

lol completely off..

i was there that night too..

This guy in a blue ute ran a red light and hit her side on.. she locked up and slid onto the gutter missing the jaycar wall by about 30cm.. lucky shewas alright just some cuts on the side of her face, blood everywhere..

where were you? i was in a 32 there..

WRX plates were BRATZ

Oh yeah thats right plated "Bratz" lol..we were drivin back from parra station towards castle hill, mate was drivin a camry, as soon we drove pass we all yelled out "Get a Real License.." lool... you probably heard us..cops just looked it at us...

spotted Blitz I think i was - 4 door 32 with 33 gtr rims?

couldnt see the plates this time, but tooted and yelled out again!

oh, was in Linfield, similar time & place to where I spotted him a while ago!

So that was you in the white commo :blush:

Oh yeah thats right plated "Bratz" lol..we were drivin back from parra station towards castle hill, mate was drivin a camry, as soon we drove pass we all yelled out "Get a Real License.." lool... you probably heard us..cops just looked it at us...

hahahahah! yeah man i heard yas, that was funny as..

i couldn't stand the chick driving the wrexy tho... she was all like..

Hey bro can you come down here, i was fully driving normally in a fully green light and some dickhead ran a red light and hit, like how the fark does that happen bro... not my fault bro swear to allah!

jesus! shutup bitch, talk normal.

hahahahah! yeah man i heard yas, that was funny as..

i couldn't stand the chick driving the wrexy tho... she was all like..

Hey bro can you come down here, i was fully driving normally in a fully green light and some dickhead ran a red light and hit, like how the fark does that happen bro... not my fault bro swear to allah!

jesus! shutup bitch, talk normal.

normally

talk normally

Yesterday spotted at Miranda:

-Grey/Gunmetal R33 4dr sedan Plates AZZ*** heading up kiora road

-Silver Series 1 with www.skylinesaustralia.com on the boot and gt-spec s15 rims turning left onto kiora rd from back of westfield. Plates AZ**** i think.

Also spotted a black gtr32 on henry lawson drive around 11:30-12pm last night parked on the side of the road chatting with another car as i drove past in my DD civic with angel eyes+hid's lol.

i was walking to my car so you wouldn't of saw me :laugh:

Spotted a gun metal 32 Gtr this morning

AUJ 97Z

i tried to wave but no body was driving it!

spotted you again this morning near milperra uni driving the oppisite way!

dont knwo if your a member here!

but hi!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...