Jump to content
SAU Community

Recommended Posts

Spotted a black R32 going down Mona Vale Road from St.Ives n turning off in Frenchs Forest

Spotted Stevo (N1GTR) at the Lowenbrau last night...

I was around the corner last night for a lil bit :O at the Argyle.

Spotted Mass in his 34 GT-R heading out of the city on Anzac bridge last night at 8:30

sweeet first official random spot i think!!

Did u notice the ugly scratch on the driver side rear bumper??? some ass hole hit it while trying to change lanes then did the runner :O lucky i got the plates. not happy at all :rofl:

Spotted a cop car tailing me from Deewhy to Newport(switching lanes when I did) running my rego etc waiting for me to do something wrong and then taking off after a bogandore ran a red light right next to me!! :worship:

Oh and spotted a white R34 and a red 31 while cruising in Newport. 31 was dodging through traffic tsk tsk..

Spotted Stevo (N1GTR) at the Lowenbrau last night...

Spotted Sasha (smasha) at the Lowenbrau last night...

...wait a sec :worship:

Spotted a black R32 going down Mona Vale Road from St.Ives n turning off in Frenchs Forest

I was around the corner last night for a lil bit :( at the Argyle.

I was at the Argyle for a bit aswel, and the fortune of war, and the........yeah, long night with a large group spread out between pubs

Here's a blast from the past for the old-school crew - I spotted a black S13 Silvia (was either very unloved or dirty) at lunchtime today (Sunday) with an SDU sticker on the front windscreen!

This was on Metella Road in Toongabbie.

Spotted an r32 gtr at waterfall last night, i was on my way to macpass (which had been raining)

Also spotted abo's new bike - looks good!!!!

AND spotted skylinegtts at Abo's place

AND spotted Sh@un at sutherland, stading on the gutter waiting to be picked up......he had the "looking for a date baby?" look going on

Spotted Sasha (smasha) at the Lowenbrau last night...

...wait a sec ;)

I was at the Argyle for a bit aswel, and the fortune of war, and the........yeah, long night with a large group spread out between pubs

It wasnt by any chance ur birthday and u were there with mates n stuff??

I was only there for about 45mins at around 10.30 i think :w00t:

spotted Anna last night :D

tee hee.... spotted joo too!! And the lovely Georgie!!

Spotted Kelly (ADORAA) on the way to work this morning, going the opposite way...

Were you giving Anna a lift to work? :P

Haha... twas me driving Kelly's car..... She was no where near it today!

thought I spied some nugget with the plates OSAKA at orange grove last nite

:P

Must of been some other nugget cos my plates are AR-36-UA now lol. RTA has to reissue me with osaka cos it ran outa rego for over 3 months, should be ready in a week or 2.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...