Jump to content
SAU Community

Recommended Posts

omg bret nice "carpet" :laugh: on your dash..... hey do you eat dinner at 3pm and in bed by 5??????

nah just playing with you

whats wrong with eating at 3 and sleeping by 5? ;)

Where abouts in Carlingford Court and did it have blue number plates?

Hahaha, it was in the parking lot outside where the front entrance is (near the now-closed Starbucks). Had normal plates, I *think* it was BRZ39P or similar.

Nope, it wasn't you, Drew - I would have recognised your car and come to say hello, the driver was looking for parking when I was on my way back to the Stagea.

I spotted an R34 GTR Z-Tune this morning....such an amazing car...shits on most skylines in aust

i would post pics but the owner doesnt want them to be posted

lol. if it is *the* genuine z tune in Aus it is unmodified externally and there are heaps of pics of it and other cars that look identical overseas.

if it is one of the couple of replicas getting around - why would you make your car look like a z tune and then not want people to see it?

Hahaha, it was in the parking lot outside where the front entrance is (near the now-closed Starbucks). Had normal plates, I *think* it was BRZ39P or similar.

Nope, it wasn't you, Drew - I would have recognised your car and come to say hello, the driver was looking for parking when I was on my way back to the Stagea.

Ah, my car lives at carlo court during the week but not in that car park lol... I wouldn't have been the car but feel free to pop into my work to say next time you are up there :)

lol. if it is *the* genuine z tune in Aus it is unmodified externally and there are heaps of pics of it and other cars that look identical overseas.

if it is one of the couple of replicas getting around - why would you make your car look like a z tune and then not want people to see it?

Pretty sure it was a real Z-Tune as it was outside Powerplay Imports with the red plates "ZTUNED"

Spotted a silver R33 in the parking lot of where the P&O cruises depart off Hickson Road at Wharf 8, Darling Harbour.

Went to pick up my sister today, and she said the same car was there again. Rego was DRE33A.

Ah, my car lives at carlo court during the week but not in that car park lol... I wouldn't have been the car but feel free to pop into my work to say next time you are up there :D

Oh, okay. Didn't know you actually work there in the centre. Next time I'm in the area I'll pop in.

spotted a couple of skylines at livo krispy late on sat

can only remember the 33 with LOZ ??? plates

If your on here hi and what was the silverish 34 you were following

cause it looked noice :D

and a maroon 33 GTR this morning at turramurra just turning off the HWY at the hall/servo

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...