Jump to content
SAU Community

Recommended Posts

I checked it out a while ago; looked like well in excess of 7k. headlights themselves are ~2500 IIRC (for genuine new GTR).

hmm i may just stay with the 33 front end especially being non turbo im a just sell it soon to get a turbo anyway doing anything expensive to it will just be lost money

I checked it out a while ago; looked like well in excess of 7k. headlights themselves are ~2500 IIRC (for genuine new GTR).

Actually (as I'm more of a go than show individual) it was a pretty cheap job.

The complete fibreglass kit was $900 from a member (Drift Shop i think) here, the headlights also from a member here (non-xenon) were $500ish, and then the sandpaper, grease/wax remover and cheapo satin black spraycans, sikaflex, pop rivets and cable ties (lol!) added up to about $100 :cheers:

The installation was fiddly to tell the truth, but fairly straightforward. After a dry-fit, and Pre-drill for the mounting holes, all of the panels needed a cut or grind here and there to sit correctly, which I ecpected for a cheap kit. The Moulds seem to be good quality, but some areas had more resin than glass so due care was required. The headlights fitted nicely with some simple DIY aluminium brackets, but still require a bit of fiddling to get the alignment perfect. The original rear arches were cut, folded,and weld stitched before sealing (Room for 285 rubber!:banana:)

I might get some build photos together and post a thread on it in a week or two.

My goal was mostly to get more wheel/suspension room, and to look tough from a distance, and have (mostly) succeeded. That said, if you like show cars don't bother with a cheap kit as you will spend weeks getting a perfect fit/finish unless you have lots of time, money, or bodywork skill.

It's a long way from finished, and my family car/daily and my 3yo daughter loves it! :yes:

Ah, see I was more looking at getting it perfect R34 GTR front end.... plus I'd need it to be installed as I am the suck when it comes to bodywork :)

I think a lot of that was labour, but yeah, new 34 xenon's are friggin pricey. given that the price of doing the conversion would be basically the cost of my car (sigh), noooot gonna bother anytime soon.

saw a few today.

- gunmetal/dark grey r35 on james ruse drive at about 4.00 pm ish.

- yellow r34 coupe turning onto shaftsbury rd in burwood not long after

- white 4 door r34 not far behind the yellow one but it kept going down parra road

- r33 parked in hurlstone park near the pub

WooHoo!

Thanks dude! Where were you? I can't remember seeing a white 33.

I was in a green 2011 fiesta lol no licence for another 3 and a half weeks :-(

Sexy looking stagea tho... Love the plates to..!!!

Should also add, spotted some very nice Skylines at Sydney Dragway last night!

This includes XKLABA who was out making the high powered GTRs look bad!! :P Pretty impressive runs and an update to that signature block required!!

Should also add, spotted some very nice Skylines at Sydney Dragway last night!

This includes XKLABA who was out making the high powered GTRs look bad!! :P Pretty impressive runs and an update to that signature block required!!

thank you, you did really good to with a new pb and an impressive trap speed, that 10 can't be to far now, :thumbsup:

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...