Jump to content
SAU Community

Recommended Posts

Hey mate thats me... thanks...

yeh wudnt have noticed you.. iv been driving my car around lately hehehe i cant help it, its still new to me :)

dont be shy to say hi next time.

I will for sure. If you see someone someone waving madly from a red 1986 Corolla or a Silver R33 S2 Sedan, that will most likely be me.

spotted sex on wheels today.... XX34XX...

:drool:

Totally sex -MASS-... totally sex!

haha you spun me out wen u rang me... i was like huh u must be standing in the car park lol... next time ill keep her in the sun so u can drool even more :)

I will for sure. If you see someone someone waving madly from a red 1986 Corolla or a Silver R33 S2 Sedan, that will most likely be me.

haha will do, ill be sure to keep the camera on hand and take a photo of u waving like a mad man, so i can stick it on here lol.

Spotted moanie on morrison rd gladesville/tennyson/putney/ryde at the western cresent roundabout at 6pm. I was in my red corolla.

oh woo!! not sure where that is, but sounds like my route home :D:)

haha you spun me out wen u rang me... i was like huh u must be standing in the car park lol... next time ill keep her in the sun so u can drool even more :P

haha will do, ill be sure to keep the camera on hand and take a photo of u waving like a mad man, so i can stick it on here lol.

hehehee... i honed right in on it! and yes please... some sun next time would be nice! :D

oh woops, and i spotted -MONA's- and caine's car in my gym car park..

:giggle:

OMGWTFBBQ who is sheng? I spotted DJ_Albert on windsor rd :) actually it was skyline day that day there was a white 33 next to you from memory

hahaa

Dj Albert was my old username lol, it was lame and more lameness so i changed it LOL

but sheng its me :D but im still albert, call me wateves GET IT :P

welllll the white one next to me was a tool, had like 10 woofer run out of 1 one channel amp, and the dude was looking through a crookerd rearvison mirror

...mm must be the subs

Spotted a big white Nissan Patrol 4WD flashing and waving at me just off castle hill road about 2mins ago.

I kinda nodded. Wasn't sure what to do actually. Who was it?

:) if you're on here.

just spotted a white r34 2door,had a big aftermarket front bar. looked hot

im pretty sure it was a blonde chick driving,,,well i hope....cause i was pervin.LoL

@ the set of lights out front of woolworths on Greystanes rd heading towards the great western.

Spotted a GT350 Skyline V35 (blue) with SAU stickers in ryde to homebush then you turned onto m4.. Plates ???-50V or somthing.

Have to say car sounds great, was in a Accent drueling over your ride

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...