Jump to content
SAU Community

Recommended Posts

I have a pretty general question about tires, currently my stag is running a set of 215 x 55 Bridgestones on the stock 7j 17" rims, the tires have quite a few screws stuck in them and they make a pretty crap noise when cornering . I have a full set of wet weather TOYO tires that were fitted to my track car, I think these will go really well on the stag. Problem is that the tires are 215 x 40 profile, I was wondering what affect going from 55 to 40 profile will have on my speedo?

Doable or not?

Link to comment
https://www.sau.com.au/forums/topic/292582-m35-tire-profiles/
Share on other sites

Thanks guys, so if i do this my wheels will be spinning 10.7% faster, so if my speedo says I'm doing 100Kph I'd actually be doing 89Km/hr not including the standard factory over read of about 7Kph.

Maybe I'll give it a miss, don't want to be the slowest thing on the highway!

I find the standard speedo is out by nearly 8km at 100km/h already...wouldn't want to make it worse...

one thing to make sure is that the front and back tyres are all the same diameter & width etc. The AWD system does allow for a minimal difference (ie. to account for uneven tyre wear) but if the difference is too great it will play up.

I'd put them on. Car will handle better. You just need to go by one of those displays at the side of the road that says how fast you are going and then you can calculate what your speedo should read to be doing 109km/hr on the motorway - there's no way you can pull max revs in top gear anyway so your real maximum speed will probably increase (or it would do if you didn't have the 180km/hr speed cut).

You can get a kit from Jaycar to correct your speedo if you need.

one thing to make sure is that the front and back tyres are all the same diameter & width etc. The AWD system does allow for a minimal difference (ie. to account for uneven tyre wear) but if the difference is too great it will play up.

LOL my stag is RWD only bud. Keeps me bright eyed and bushy tailed on wet mornings :)

Cheers for the info Kiwi, might check out Jaycar.

  • 3 weeks later...
might check out Jaycar.

Let me know how you get on with a Jaycar kit if you go that route, I'm keen to recalibrate my speedo also. It seems to read 6-7km/h under at 100km/h. It wouldn't be too bad, but the factory cruise control only goes up to 110km/h, which means 103km/h real, and that sucks :)

VQ25DD,RWD, RX, cruise, navi, HID, but only 16" wheels (wacky size too - 205-65-16)

I have a pretty general question about tires, currently my stag is running a set of 215 x 55 Bridgestones on the stock 7j 17" rims, the tires have quite a few screws stuck in them and they make a pretty crap noise when cornering . I have a full set of wet weather TOYO tires that were fitted to my track car, I think these will go really well on the stag. Problem is that the tires are 215 x 40 profile, I was wondering what affect going from 55 to 40 profile will have on my speedo?

Doable or not?

http://www.1010tires.com/tiresizecalculator.asp

Just remember to keep it under or over 3% variance

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • LOL, all of the CAI like Craig I just need to put a hole saw through my bumper Done and dusted, the car runs, which is nice, I'll take it for a spin when the weather clears up Just need to put the bumper back on for good
    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
×
×
  • Create New...