Jump to content
SAU Community

Recommended Posts

What BOV are you guys running for high boost settings? eg. 1.7bar-2bar?

Currently i am having issues with my BOVs. I have a HKS SSQV which is shyt and now my Greedy Type RS is giving me issues as well..

One time the RS had its valve stuck open and HKS had always have problem with stalling.

I dont have much confidence in these 2 brands now and im worried it might destroy my compressor shaft if i continue running on those BOVs.

I am serching for something more dependable and I was wondering are Tial BOVs any good?

Another question.

Do you guys run two BOVs at the intercooler to intake or one on each side of intercooler?

What spring rates?

Comments and feedbacks are most welcome.

Link to comment
https://www.sau.com.au/forums/topic/295386-high-boost-blow-off-valves/
Share on other sites

While we are on the subject of BOV's I'd like to ask about location of them.

I was under the impression the best place was as close to the throttle body as possible. That way, when the throttle closes and the BOV opens the majority of the charge air continues flowing in the same direction.

The other day I was looking on the turbobygarrett website and it stated the best place for the BOV was as close to the compressor outlet as practical. To me this doesn't make sense as all the charge air in the pipes/intercooler has to reverse flow to exit the BOV.

On RB's the standard BOV is pretty close to the thottle. And from what I can recall, on SR20's the BOV is located near the throttle and the return pipe crosses back over to the other side of the engine to get back to the compressor inlet.

In both cases (and you see this alot in aftermarket piping kits) the BOV is usually located on the hot pipe, next to the compressor inlet in order to shorten the return pipe.

Edited by daisu
  • 3 months later...

digging up an old thread rather than starting a new one.

and not 'quite' the same question but here goes,

Has anyone ran GTR Bov's Pre cooler?

I've finally sourced some 33 GTR Bovs, and I was wondering if I could place them Beofre the cooler, as this will make the return to the intake a heck of a lot shorter/simpler. If I mount them in the same position as the GTR, I've got to run a 2" return pipe all the way from the cooler exit right back to the intake pipe. And the factory plastic return wont work with my custom piping/cooler setup.

I'm olny concerned as I know the GTR Bov's have the rubber/plastic seat and I'm worried about them melting due to the added heat being plumbed in pre cooler compared the the factory 'after the cooler'.

cheers

Would like some info in this.. possibly a pm to me would be real nice if you have the time?

I suspect mine is leaking.. How do you know if yours has the soft spring or the other one? how do you have it hooked up? do you have both lines connected or just the one?

ive played around with mine for ages....

I ran a Greddy type R with the soft spring at around 1.9 bar with no problems.

+3 For stock GTR BOV's

28psi and no leaks...

As for swapping from aftermarket to GTR ... Stock, the GTR BOV's are open at idle, so make shure you plumb them back before the AFM- or put filters on them for MAP sensor cars.

Melt??? I doubt it. They're so cheap to replace I wouldn't worry about it.

I think it was Nizpro that used to use them for boost controll... Good bit of kit!

Yes I know they open at idle, so yep making new intake to accommodate the return pipe.

I was only concerned they would melt as they will see heat they were never going to see mounted after the cooler. And if they did happen to fail I had visions of crap (Hard plastic) finding its way back to the intake and into my comp wheel..... I've had a look at the plastic, its looks pretty sturdy stuff tho.

I'm not expecting it to happen, I'm sure nissan built them to take 10 times the heat they were ever going to see. But it doesn't cost to ask, and maybe avoid a potential headache.

and as for cheap, not really - and thats when you can get them.

I run GTR BOV's pre-cooler.

I have a backpressure problem that i'm sorting out, we think it's due to the cooler piping bends and chamber changes made a while ago. (been tested, so its 100% something that was changed)

So they blow open over 16psi, but otherwise no issue and they will be perfectly fine pre-cooler. Just a bastard to fit them there :D

I suspected you would run them pre cooler on the 31, I think I sent you a PM but maybe it didnt send.

I think I've got it nutted out, Took me awhile tho.

I'll post up some pics once I'm done

You might well have - i've got ... to many atm.

Need to sit down for 2-3 hours and go through them all... avoiding it :D

I did have a single BOV before cooler, but now with 2x its pre-cooler. It's not very "clean", a tad messy looking but works fine.

I have a split A/C setup (factory nissan) so i couldnt put them on the drivers side unfortunately, not quite enough room otherwise post cooler they would have gone.

What BOV are you guys running for high boost settings? eg. 1.7bar-2bar?

Currently i am having issues with my BOVs. I have a HKS SSQV which is shyt and now my Greedy Type RS is giving me issues as well..

One time the RS had its valve stuck open and HKS had always have problem with stalling.

I dont have much confidence in these 2 brands now and im worried it might destroy my compressor shaft if i continue running on those BOVs.

I am serching for something more dependable and I was wondering are Tial BOVs any good?

Another question.

Do you guys run two BOVs at the intercooler to intake or one on each side of intercooler?

What spring rates?

Comments and feedbacks are most welcome.

1.8bar. bog stock 32gtr bov's

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...