Jump to content
SAU Community

Recommended Posts

I wish, each piece is indexed into a spiral to fit the confined space then sanded internally to smooth it out. I would be doing nearly as much welding with the pressed doughnuts and they aren't cheap or tight enough.

The hole in the doughnut would need to be no bigger than about an inch.

I don't mind the welding, its good practice. :huh:

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

why dont you get it ceramic coated??

Cost.

I got enough ceramic wrap to do 20 inductions for $50, and I aint ripping the exhaust manifolds off to coat unless I have custom ones to go on. (with a gt3076 of course)

Edited by scotty nm35

Alright, so latest (and last) fuel economy update for those that are interested

Usual trips to and from work with a (very) heavy foot :P and about 100kms worth of freeway cruising

65L

549kms

roughly 8.5km/L or 11.8L/100kms.... so still good IMO

Edited by iamhe77
Alright, so latest (and last) fuel economy update for those that are interested

Usual trips to and from work with a (very) heavy foot :D and about 100kms worth of freeway cruising

65L

549kms

roughly 8.5km/L or 11.8L/100kms.... so still good IMO

not bad without a tune! :D

22kw increase, not bad I thought.

Cihan thought I may be maxing the compressor so I guess i need to free up more restrictions, like the turbo outlet pipe next. Must be well over 400 horse at the crank now so the ATP highflow is doing pretty well considering.

Edited by scotty nm35
Mmm, need to find some way of jigging these up off the car. Anybody got a spare turbo laying around? :D

will do soon, Cam had it but it has gone to be rebuilt and the broken one will be off the car next week.

I cen send it to you when I get it back if that will speed up the process.

Cheers

Andy

will do soon, Cam had it but it has gone to be rebuilt and the broken one will be off the car next week.

I can send it to you when I get it back if that will speed up the process.

Cheers

Andy

Turbo broad minded person!!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dredgggggeeee time; I have recently finally started driving the car. It sat for so long that the fuel tank gave birth to rust sludge and blocked my lift pump sock and one of my walbro 460's and left grime, rust chunks and muck all through the surge tank and system. I decided to commit and pull the trigger on an oem r32 gtr fuel tank and Frenchys twin 460 / sender / surge tank hanger combo and all new larger lines and fittings etc, also boost doc heater hose kit / new heater core and a heap of other bits and shits like wideband sensor installed in the dump and Syltech iacv + lines and all wired and added to current tune. now having lightly driven it a couple times without issue, I can happily report on the hta3076 in its current tune. still no boost control switched on, 20psi gate springs, car makes 22psi at 3200rpm in 6th gear with 30-50% TPS from cruise at 100kmh. Going by the old graph, this means it should be making 300-325whp at the same numbers above. Very very responsive setup under true road driving loads. all that's left for the build is body loom + PDM, finish the remote aircon setup, install carbon fibre parts and go for full tune and 30psi. the 315 rear tyres are now performing like they're 195's, wheel spin in any gear at almost any rpm, whereas my previous setup hooked up in 3rd no issue, albeit Nt01's back then / RB25 5spd vs (new) old date r888r's Z34 6spd now, + obviously all the support upgrades I listed in the quoted post above. car sits at 1-3psi on cruise at 100kmh, expectations totally exceeded and I'm beyond stoked with all this so far. IMG_4848.mov
    • I've also been eyeing their rear axles for my car. I purchased seat mounts from them about 7 years ago and they were hot garbage so I've been a little wary about purchasing them. With that being said, please buy them and get back to us haha. 
    • Can a moderator please move this into the right category.. I've accidently put this into racing build thread 🤦🏽‍♂️
×
×
  • Create New...