Jump to content
SAU Community

Recommended Posts

Hi guys,

I recently brought an R32 as a daily, it's stock, runs stock boost etc.

It pings it absolute face off above about 4500rpm.

I wound the timing back as far as it can go (yes I know it's clockwise on the CAS) and it was better but I can still hear a few pings and that is will like 20RWKW down low because the timing is so retarded.

This is with 98 octane fuel (BP Ultimate) I have tried different fuels with the same result.

It doesn't ping coming on to boost which is kinda wierd, only at about 4000rpm+ once it starts to do something. Stock turbo is fully spooled way before then.

Any idea's guys? The boost is around 5psi at the intake manifold, also confirmed with another gauge.

I have an RB30DET in an R33 as a daily driver and I remember when that had the stock RB25DET in it, I use to run 12psi on 18 degrease of timing and it never pinged on 98 octane fuel. :)

Stock coil packs, Also have a receipt from the previous owner where it has just had new plugs put in it at a work shop. Not sure what they are and haven't pulled one out to look but I assume they would just be stock gap.

Not sure how spark plug gap or brand can make it ping.

It doesn't miss at all so I assumed it wouldn't be a spark related issue.

:) why didn't I think of that before...

I will stick a fuel pressure reg on and see how much fuel pressure the stock pump is holding... kinda have to test that under load though...

I think I have a set of RB20DET injectors lying around some where I will try changing them over... I hate removing intake manifolds on RBs so much :)

Will also try replacing the pump if I can find one lying around. I have a Bosch 044 lying around so I could run that in-line and see if that helps.

It's wierd cuz this car has really no power, I guess around 100RWKW if it's lucky. I would have thought the stock fuel gear wouldn't have a problem with it unless an injector is all clogged up or the stock fuel pressure reg is dying.

Edited by Finny

I replaced the pump with a new pump, voltages are fine. I really don't think it is a fuel issue as the car doesn't hesitate or have any signs of fuel starvation.

It also doesn't ping for like the first 2 minutes of driving until the car gets hot, I thought it could just need a cooler upgrade but no other R32 that I have seen pinged with stock cooler, In fact a friend of mine had an R32 with more than stock timing, 12psi and stock cooler and that had no issues.

I changed the computer to one that had been tuned to 180RWKW with stock injectors and the car will not rev. It has classic retarded timing issues like very slow free rev and at about 4500rpm it just wouldn't free rev any higher. Another sign or retarded timing was the exhaust was pooping heaps of flames due to the exhaust valve opening while the fuel was still burning. I didn't pay much attention to this as this ecu has not been tried in an R32 since it was brought off ebay by a friend so it could just be a dud tune. Also I adjusted the timing with the cas and it didn't help.

check if the vacuum line to the factory FPR is connected and not damaged. Sounds like a fuelling problem, when the car is cold by default it will run more rich hence less/no ping.

I suspect a faulty FPR or fuel pump.

A friend just pointed out to me, it's probably got like bosch temp 5 plugs as it had new plugs put in at a work shop, they used bosch plugs and a temp 5 in a bosch plug is like a temp 3 in an NGK. I am going to put some NGK temp 8 plugs in it and see if that fixes the issue.

sounds like ur timing belt hasnt been installed properly, check that first, spark plugs dont make u ping !! >.<

Agreed, he really needs to check the belt and see where all the markings are.

A betting man would put money on this.

I replaced the pump with a new pump, voltages are fine. I really don't think it is a fuel issue as the car doesn't hesitate or have any signs of fuel starvation.
Of course it is - it's pinging!
It also doesn't ping for like the first 2 minutes of driving until the car gets hot,
Because the engine is cold, and the ECU is running the engine rich.
... it's probably got like bosch temp 5 plugs ...
Have you actually looked to see what plugs are installed?

You still haven't told us what fuel pressure the engine is running.

spark plugs dont make u ping !!
If the plug is running too hot, it can pre-ignite the mixture (works like a glowplug).

You changed the pump and injectors but not the fuel filter??

You can measure all the fuel pressure you like but you also need to check the system flow, thats just as important.

Use a timing light; that will tell you where the timing actually is and if there is a possibility of the cam timing being out.

and also:

Are you sure its actually pinging?

Some boost leaks sometimes sound like knocking. Just an idea.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes, I know🙄 but the sequential is not in my budget... don't want to reduce power neither, so looks like I'm stuck in the rabbit hole🤣
    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
×
×
  • Create New...