Jump to content
SAU Community

R34 Gtt Overheated Due To No Water/coolant, Now Engine Light

Alien

By Alien,
in Engines & Forced Induction

 Share

Recommended Posts

Alien Grand Master

Alien

Posted
Posted

Hey guys

Long time since I've been here as I havent been driving my 34 for months now. Due to this, after taking it for a drive yesterday, after driving for about 20 mins, the car started going a bit sluggish and lost all power and had engine light on. I pulled over and as I thought, overheat. There was no water/coolant left at all and wat was left was extremenly hot and boiling. I let the car cool off a bit while I waited to get some water bottles delivered to me and then filled up around 5 litres of water into radiator and the water/coolant tank. The car started up fine, runs fine and everything but the orange engine light stays on in the dash. Its not coilpacks as I've installed Splitfires already and the car still runs fine.

How can I get rid of this engine light now? Is it meant to stay on until somebody manually clears it with a diagnostic tool? Or is there something or some parts that stuffed up due to overheat? Also, should I go get a full radiator flush and who is a good mechanic these days for skylines around Sydney west?

Thanks guys

DarkZ

vidospace Mentor

vidospace

Posted
Posted

Yes you should flush the radiator.

You shouldnt have filled it with water only, it needs coolant specifically.

The bigger issue than the light on the dash is why it ran out of coolant at all? Was it blowing smoke? You might have a blown cylinder head too!

Re the light though. Yes you can reset it with a consult cable.

noone Experienced

noone

Posted
Posted

As above I would be just as worried about where the water went

and probable head gasket damage

On most cars disconnecting the battery overnight or disconnect than stand on the brakes for 30 seconds

tends to clear engine lights, resets the computer

however will come back on when it starts if the fault is still there?????

Have not tried this on a skyline but works on nearly everything else I have tried it on

West Grand Master

West

Posted
Posted

RB's are tough nut when it comes to the over-heat thing, i once left my radiator cap out, drove the car for 20km or more until i see steam coming out of the bonnet. Shat myself but the bloody thing still going even after 3 years later.

666DAN Grand Master

666DAN

Posted
Posted (edited)

Yep best to run the diagnostic and see what it says....could be anything from a damaged sensor to coolant water shorting something out. Until it's rectified the light won't go.

Saying that though, I do recall a something about the ECU needing to be reset after logging an overheat code, but yeah follow the thing below and it shows how to reset with a paper clip

Diagnostic

Edited by 666DAN
Alien Grand Master

Alien

Posted
  • Author
Posted

thanks for the info guys

I havent driven the car for a long time and maybe from recent heat the coolant just evapourated, if thats even possible. I will flush it out asap, just need to find a good mechanic specialising in lines.

Cheers

  • 3 weeks later...
Alien Grand Master

Alien

Posted
  • Author
Posted

hey guys

I havent had a chance to take the car to a mechanic so I had a look just before and its still spitting out water from underneath the car. So I had a look at engine bay and found a fairly high pressured leak - I'm assuming a crack at one of the pipes. Its all the way at the back of the engine so I can't really spot it.

Is this just a matter of replacing the plastic pipes or is it something more serious?

Cheers and happy new year!

DECIM8 Grand Master

DECIM8

Posted
Posted (edited)

I know what it is.. Its the part sitting behind the firewall. Exact same issue I had with my car. I made a thread about it ages ago.

The part corrodes over time as its metal, I figure its the same thing.

P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

Position of the leak is drivers side about 10-20 in from the side of the engine and about 30cm down and in the worst spot you can imagine.

Edited by DECIM8
Jezza-gtR Mentor

Jezza-gtR

Posted
Posted
P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

A car does need coolant, the main function of coolant is to raise the boiling point of water. You won't get far with 100% water in your system.

Alien Grand Master

Alien

Posted
  • Author
Posted
I know what it is.. Its the part sitting behind the firewall. Exact same issue I had with my car. I made a thread about it ages ago.

The part corrodes over time as its metal, I figure its the same thing.

P.S the car doesnt need coolant thats just to stop it rusting. Good to see you back thought you might have written off the car/sold it as I spotted it for sale on st george website. weird.

Position of the leak is drivers side about 10-20 in from the side of the engine and about 30cm down and in the worst spot you can imagine.

Hey dude long time no speak

Are you sure it was my exact 34 that was on sale as I never had it up for sale on any classifieds site. Which St George site?

As for the leak, how do I go about reaching for it and whats the replacement part I need and where could I grab it from? Do you have a link to the thread?

Thanks man

l_uk3y Proficient

l_uk3y

Posted
Posted

Now someone feel free to correct me if they want. But to my knowledge the coolant actually increases the waters boiling temperature above 100 degrees. (besides other tasks). Either way I've never heard anything good about running water only.

That said I ran water only and lost my radiator cap on my old pintara about 6 or so years ago. Had no issues driving around like that (with no cap) for a week before I got a new cap (I don't condone this at all though). I babied the car the whole time though

JonnoHR31 Grand Master

JonnoHR31

Posted
Posted

water transfers heat a little better than coolant but its not a good idea in a RB, alloy head doesnt like corrosive water. the pressure of the system raises the boiling point higher than 100 with straight water and coolant is higher again

Alien Grand Master

Alien

Posted
  • Author
Posted

I found the leak... it is in the worst part of the engine bay, right behing the engine. Its the metal bit where you clamp on a thin hose to a bigger hose. No idea how I can fix this or anybody else as it is practicaly unreachable with tools etc. I was able to get my hand in there and touch the crack to stop the leak but how can I actually repair it? Can I just change the whole hose somehow?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      R34 GT-T cycling ABS pump

      By Kinkstaah · Posted

      Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • GTSBoy
      33 GTR Broken front wheel knuckle

      By GTSBoy · Posted

      That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • R32 TT
      33 GTR Broken front wheel knuckle

      By R32 TT · Posted

      Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • MBS206
      33 GTR Broken front wheel knuckle

      By MBS206 · Posted

      Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • GTSBoy
      R34 auto to manual conversion help

      By GTSBoy · Posted

      The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...