Jump to content
SAU Community

Recommended Posts

This could be good. I had an RMR30 that I must confess I neglected and the Auto conked out at 600. Of course it was only an L24E. But at least the auto matched the engine. I am hoping the S1 will give, say, 75%. I would be happy as a cop in shit.

I am looking at some mods to prolong The S1 life.

Edited by 66yostagea

Not exactly the same, I know, but my r31 (rb30e) had done over 500,000 kays when I sold it, 300,000 of that in my hands, never used oil, never missed a beat except corroded plug on CAS, ($20 fix).

RB's are built with extremely accurate tolerances. Also the crank girdle gives a very stiff block structure which can only help as power increases. As such, moderately powered examples that are not revved constantly within an inch of their lives are a very long lived proposition.

A C34 will rust doors away before the drive line gives out. My parents' VL clocked up ~430k before it got written off, my Stag is at 120k and I expect another 200k out of it before I think about rebuilding the motor. The turbocharger should last just as long if it's given clean air and clean oil. My L28ET is at about 300K and is being retired in the quest for more HP, not because it's stuffed...

Mine was in excellent condition at 134,000 k's... then I put some coarse grit blasting compound in the oil and drove it for a couple of thousand and it was *still* going strong. Decided to rebuild to be safe :D

Mine has 138,000 and i bought it to years ago and it had 60,000. Ive started towing a trailer with about a tonne of weight everyday about 7months ago and it tows well. never cost me any serious money yet. Service every 5000km, although my realese bearing is realy noisy ive never had any dramas "touch wood". Thats just routine maintenence.

I know its not a 25 but... I have witnessed a RB30ET (Factory Turbo VL not a +T)

on the dyno with a genuine 600,000 + Kms on the clock.

Only on the dyno to check everything still looking healthy.

The owner had only replaced the injectors and AFM in its time,

with general maintenance of course.

Aren't turbos a maintenance item at 100k km?

Also, we need to remember that some members cars km's won't be genuine...

IMO, 'Factory' Turbos are abit of a 'luck of the draw'. Ive heard of RB turbos letting go (seals, wheels etc) at a

very early age/Milage and others doing 200k + km's.

The MOST common problem I've come across with mine and several other friends turbos, are the

'Manifold to Turbo' gasket. Generally its just the Nuts coming loose and just need a nip up. The 'Turbo tabs'

do a mighty good job at preventing any further implications. When the nuts loosen, a strange 'whistle/whine'

can be heard very clearly when under full song. My conclusion on the problem is poor maintenance regarding

the exhaust mounts/design etc. Just swinging around hanging all its weight on the back of the turbo can

be harmful.

Regarding the 'Genuine' KM's... I got mine a month after coming off the docks with 48,***kms. I wouldnt

be suprised in the slightest if they were wound back or tampered with in some way. Abit too good/unbelievable to be true... ;)

Aren't turbos a maintenance item at 100k km?

Also, we need to remember that some members cars km's won't be genuine...

This is true for the M35 but not sure about the C34. The M35's have a similar turbo but run slightly higher boost (11.7psi for RS/RX and 15? for ARX) so presumably this would have an effect on the lifespan of the turbo.

Mine has now done nearly 110,000 and the turbo still appears to be going strong (completely stock). Fingers crossed.

So far the only actual diagnosed "fault" has been the throttle body getting clogged up making the butterfly a bit sticky - which caused it to stall occasionally. I cleaned it out myself, carried out the idle-relearn procedure (see the DIY/howto thread at the top of the stagea section) and it was all fixed.

Total Cost: $0

The kms on my M35 stagea are more than likely genuine since I imported it through someone I know and trust, and who has been dealing with the same agents in japan for years.

My last stagea was a series 2 which I bought from a dealer on the Gold Coast. 28000kms for a 1999 model seemed a bit too far fetched - however it did go all the way to 100,000km without the timing belt breaking so either they changed it before I got it, or it had really done somewhere around 128,000km. Interior condition was very good - however there was a slight oil leak from the rocker cover.... That stagea proved to be pretty reliable although it did have a cracked exhaust manifold and suspect turbo, both which needed replacing. One of the shock absorbers also needed replacing - which was done under dealer warranty. Other than these initial problems (which existed when I bought the car), I really had no major issues at all in the 2 years I owned the car.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
    • heh, aint no R32 ever meeting modern targa cage rules unless the driver is veeeery short OP, good luck with the sale, since its already in the land of freedom I'm sure you will find a good buyer.
×
×
  • Create New...