Jump to content
SAU Community

Recommended Posts

I have noticed sometimes the fuel gauge in my car drops from 1/4 tank to empty with the light on, in the space of a few k's. I read the v35's are having similar issues and wanted to know if anyone else has this problem.

I pulled the pump out to check but couldn't find anything obvious wrong with the sender resister.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/
Share on other sites

In the space of how many km's Scott?

Mine goes from 1/4 to light on after ~140kms normal driving :)

or

1/4 to light on after ~70-80kms of fun driving

I have noticed at times that the light will be on when I shut the car down, then an hour or so later when I go out again I will have just over 1/8 of tank left with no light on (nor does it come on for a while either).

Can also behave differently on different fuels.... Vpower will drop from 1/4 to nothing much faster than Ultimate.... and don't get me started on Vortex98 :ninja:

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991205
Share on other sites

Mine fluctuates the whole time, not just below the 1/4 mark. It can be below the 3/4 mark and then 5 minutes later its showing just above it...

I've learnt not to pay that much attention to it - since its usually just a "rough indication" rather than an accurate measurement.

Lately I filled up when the needle was just above empty (as in very very close to the empty line), but only got 54L in. Other times its been on the empty mark and I've managed to get around 62+L in.

From 1/4 to empty I normally get around 50-80km maximum.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991263
Share on other sites

It goes down fast at the end of the tank and probably does exactly the same thing. I am not that worried as I just fill up when the light comes on.

Cheers

Andy

I tend to not pay attention to light unless i am over 400km's in that tank haha.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4991559
Share on other sites

Mine drops to light on sometimes after one boot onto the freeway then stays there. If I switch the ignition off and on, its back up to where it was.

Im guessing there is a dry solder joint there somewhere, anyone know where the electronics is for the sensor? Let me guess, dash out?

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-4992088
Share on other sites

  • 1 month later...

Lately my fuel gauge has been getting much worse. Rather than giving me a pretty close "ballpark" reading, its now often wildly inaccurate. I've seen it nearly at the half way mark after just 130km or so, then I'll actually manage somewhere near 200km before it goes below the half way mark, then later it could be back up between 1/2 and 3/4...its just all over the place, often out by more than 1/4 of a tank!

Not sure if its just a faulty sensor but its very annoying. Soon I'll be using the kms since last fuel stop to determine how much fuel is in the tank...on a 2003 model car!!

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5056072
Share on other sites

Lately my fuel gauge has been getting much worse. Rather than giving me a pretty close "ballpark" reading, its now often wildly inaccurate. I've seen it nearly at the half way mark after just 130km or so, then I'll actually manage somewhere near 200km before it goes below the half way mark, then later it could be back up between 1/2 and 3/4...its just all over the place, often out by more than 1/4 of a tank!

Not sure if its just a faulty sensor but its very annoying. Soon I'll be using the kms since last fuel stop to determine how much fuel is in the tank...on a 2003 model car!!

I sometimes get that, seems to be the carbon on the sensor wearing out as I pulled it out for a look. If you switch the ignition off and on, it goes back up to where it should be.

I wonder if you can buy the liquid carbon and repaint it...

Edited by scotty nm35
Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5056387
Share on other sites

after fixing my turbo pressure pipe. i have been clocking 500km's easily in the volvo..

and this is with the same thirsty driving i was doing when i was getting 400's if not more pedal now i have more boost :)

?? what pipe is that?

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5057959
Share on other sites

rubber hose near washer bottle to plenum area..

You mean the one that goes to the boost sensor (ie. the sensor in the little oval shaped black box that sends the boost readout to the in-dash guage) ?

Interesting, I fixed that sensor a few months ago after reading how to do it on here (power connections inside it needed re-soldering) but at the same time the factory hose split and continued to split every time i cut it and re-attached it...so I've replaced it with a similar sized hose but this one keeps falling off the plenum side since there's no "lip" to hold it on. Its been bothering me in the back of my mind ever since (ie. vacuum hose off cant be good) but I just haven't gotten around to fixing it since it didn't seem to upset performance.

Now that you mention it the fuel economy could well have started to go bad around the time I fixed that sensor...was getting mid 12's (L/100km) and now its consistently in the high 13's if not low 14's... :P

If thats all it is then I feel a bit silly for leaving it so long...

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5060142
Share on other sites

Im guessing Angus means the 60mm black rubber pipe with the bend next to the washer bottle.

The hose you are talking about, the 3 or 4mm one will need to be replaced on most of the M35's coming in as they are very brittle. It only affects the boost meter in the dash so im not even sure all M35's have it. Definitely wont be the source of your bad economy, probably the heat doing that as the ecu is adding fuel as the inlet temps go up I think.

Link to comment
https://www.sau.com.au/forums/topic/300455-m35-fuel-gauge/#findComment-5060484
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have a look at that (shitty) pic I posted. You can see AN -4 braided line coming to a -4 to 1/8 BSPT adapter, into a 1/8 BSPT T piece. The Haltech pressure sender is screwed into the long arm of the sender and factory sender (pre your pic) into the T side. You can also see the cable tie holding the whole contraption in place. Is it better than mounting the sender direct to your engine fitting......yes because it removes that vibration as the engine revs out 50 times every lap and that factory sender is pretty big. Is it necessary for you......well I've got no idea, I just don't like something important failing twice so over-engineer it to the moon!
    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
×
×
  • Create New...