Jump to content
SAU Community

Recommended Posts

I would love to get my setup a bit more responsive than it is now, I have a hypergear atr28/g3 highflow on an auto rb25neo. Have nistune, exhaust, t-bar boost control stock injectors etc.

Getting 230rwkw at 15psi which is great but boost doesn't reach peak till almost 4000rpm.

Would changing the boost control to ebc or changing the stock actuator help it boost quicker or is it just the size of the turbo? Anything else i can add on other than a high stall on the auto?

Cheers...

shorter cooler pipen wil help a lil bit, dont go ebc,...... that equals more lag and spikes then tpeice, (been down the road myself $400 ebc = shit compare to $20 mech T-peice) maybe ur manifold aswell?

go with a decent EBC and you will notice a difference. with a t-piece you cant factor in the boost drop off that usually happens higher in the rev range, EBC can factor all this in.

4000rpm/15psi is average for 230rwkw.

Are you sure the actuator on there is solid and holding the gate shut? A few GCG hi-flows suffered from this in the earlu day where the preload was not enough.

Do a dyno run with a boost plot. Watch what it is like and it will tell you if a decent EBC will help you. If the boost plot comes on nice and strong and holds boost to redline than atleast you know an EBC will not help you.

I agree that 4000rpm to hit 15psi on a highflow is a bit average.

Edited by PM-R33

Regarding tuners i have used both status tuning and chasers and their both excellent tuners. All i know regarding the actuator is that its the stock neo one. would this be creeping open? dont know what the standard tension is but have heard of people using 14psi actuators?

Regarding tuners i have used both status tuning and chasers and their both excellent tuners. All i know regarding the actuator is that its the stock neo one. would this be creeping open? dont know what the standard tension is but have heard of people using 14psi actuators?

Ask trent what he thinks about it then. Im sure he has a big wealth of knowledge :blink:

take the vac line off the actuator and see what rpm you hit your target boost. then see what sort of difference there is between that and what it normally is

depending what the tune is like atm, more timing coming onto boost can make a huge difference. i've added more than 20degrees of timing coming onto boost on my car from where a "professional" tuner had it, car feels completely different

take the vac line off the actuator and see what rpm you hit your target boost. then see what sort of difference there is between that and what it normally is

Due to potential danger of this IMO its a bit reckless to suggest it without mentioning how to avoid the risk, so you should add to that "back off a soon as you hit you hit 15psi, or you could potentially damage the motor". And maybe also what this will achieve - "if the boost comes on earlier then you have a boost control issue. ". Perhaps the OP knows these things, perhaps not.

shorter cooler pipen wil help a lil bit, dont go ebc,...... that equals more lag and spikes then tpeice, (been down the road myself $400 ebc = shit compare to $20 mech T-peice) maybe ur manifold aswell?

I disagree. A PROPERLY SETUP EBC will work at least as well as a t piece, and should work better.

Nitrous Oxide! it will bring it on REAL quick!

3lt bottom end will too.

Port work and cams

Higher static CR

Better bottomend/off boost tuning

Cam gear adjustment

Ball bearing core and billet comp wheel

Methanol and a bunch of timing

Wire the wastegate shut

Bigger/better dump pipe and exhaust set up

Heavier right foot

Get a bigger actuator before you get an EBC.

OR

Live with it... you have to sacrifice somthing for more power.

check the actuator and preload

check diff gears (manual has different to auto)

check tune

check tune

check tune

did i mention check the tune? ignition timing plays a bit part in how the car performs and more importantly comes on boost

check basics, check base timing with a timing light and make sure its correct , ie sluggish timing makes the car perform low across the board

i assume you want more responsivenesss since the turbo has been fitted

so we can assume its not an actual car problem, but more of a tune related problem, since the new turbo went on

so either the turbo is junk or the tune is poor or both

I disagree. A PROPERLY SETUP EBC will work at least as well as a t piece, and should work better.

Lol at least as well?? its $400 compare to $20 ??

if he has a boost holding issue it can also be an erray of things...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
    • I suppose it was relatively stock too, the JZ motor handle most mods thrown at them without even breaking a sweat 
    • I saw your intro update, are you sure you've actually had a starter motor failure? You mention it could be the alarm causing it. I'm assuming you've got a no start issue, but what are the exact symptoms, as there could be a few reasons it has stopped wanting to start.
×
×
  • Create New...