Jump to content
SAU Community

Recommended Posts

I know Fatz is telling the truth, I read the same thing in a TinTin comic book!

Gotta love the 4wd megga power action. I knew there was a reason WRC cars are built, set up and driven like that WRX for a reason.

However, My experience has shown that a lap that felt way fast with a hint of sliding about wasn't actually my fastest. Disappointingly, it was the precise and slower feeling(less exciting) ones.

I do like the exciting ones much more, Harry has lots of them everywhere at Lakeside, and holds me up doing it. We turned a 59.?? sec on the first flying lap and only a 60.??sec on the 2nd with heaps of exciting moments all over the place, most exciting on the change of direction and elevation under the bridge!!!!

Edited by Noddy
  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Thanks everyone for your comments. Since there's a mixed response i'll try getting a little looser instead of staying dead clean and see how it goes next Saturday at Wakefiled.

I agree with roy, I went quite a bit quicker a wakie by braking earlier and being easier on the throttle....untill it smashed the piston rings to bits lol.

but give it a go, with the 4wd it may just work

nah the tighter the track the more likely you are to get away with a bit of sliding. You can't afford to compromise mid corner speed or corner exit on a quick turn (eg turn1 at Eastern Creek), but you can do whatever the hell you like in a slow corner like turn [email protected] long as you are pointing the right way at the end of the corner.

Speaking of wakefield.....sliding the rear of the car through the top of the track (4-5-6) is a lovely way to get through there quickly.

and equally in a slow FWD car with lots of understeer, turn in very early and slide across the apex to maintain corner speed as best you can.

basically...its just not a simple yes or no! sliding a little can be faster but not in a long race.

Yeh, i dunno!?!?!?! As per my first post, i do believe that straight is generally always going to be the quickest way. If you are going sideways then you are not going forwards. But i suppose the big differentiation is are you sliding the whole car toward to exit of a corner, (like Duncan suggests in turns 4-5-6) or whether you are wagging the tale in and out of corners where you are lifting or using a fair bit of lock to control....rather then balance the thing on the throttle.

LOL, but yeh, easiest thing to do to improve your lap time is get someone to move the timing beacon up 100mtrs on your hot lap

LOL, but yeh, easiest thing to do to improve your lap time is get someone to move the timing beacon up 100mtrs on your hot lap

I'll be trying iPhone+Tomtom Cradle+Harrys Lap timer so there'll be no cheating on the timing! I can also get details corner speed etc so in theory i'll be able to tell if clean or dirty is faster, but i doubt i'm anywhere near good/consistent enough make that call...

The last Oran Park day I did, with the instructor, I got congratulated for my "nicely controlled corner exit slide" as I came over the flip flop, basically had about 10 - 20 degrees (Referencing the steering wheel here) of opposite lock, and just drove it off the corner with a heap of throttle... His words were "That's better! THAT'S how you do it!"

But it is a common technique in a GTR to trail brake to during turn in. I usually do. The down side is that it can put you at a difficult spot in the mid corner as the car will want to understeer as you get off the brakes.

Couldn't you drive past that by pointing the nose in a bit further than the apex as you approach it? Aim the car so that, if it had perfect traction, it'd clip the inside of the corner before the apex.

As you come off the brakes and you understeer, the nose runs wide and clips the apex. The understeer also lets you get on the gas a little earlier/harder as the rear of the car will spend some of its time returning to neutral before oversteering. Hopefully in that period ATTESSA has reacted, and by the time your car chassis hits neutral balance the torque's been sent to the front wheels and you come out with good traction on all tyres.

He probably said that because you had already messed up the corner exit but handled it well. As opposed to backing off the throttle completely which would have cost you more time in that situation?

bah, watch and learn...

OK, so Brocky was a little looser than ideal in a couple of spots, but if you want to squeeze every last tenth out of it for a single fastest lap, you have to walk that line. The very start of the video is what sums it up best for me; Brocky coming onto the pit straight with the car looking nice and smooth, yet the driver sawing at the wheel - perfectly on the edge!

Edited by hrd-hr30

I think if you can slide the car at the right time, at the right angle. Yes, it's quicker.

But the problem lies in being consistent repeatably. I'm no professional and it's difficult to slide the car the same way, every corner, every lap.

Keeping it straight and just on the edge of losing grip is more controllable and easier to repeat more consistently. (for me anyway)

My 2 cents.

Edited by nismoman

Dunno if this applies as much to modern slicks (I've never driven on them) but on road tyres and the old race tyres, the tyres achieved maximum grip with a slight amount of slip (about 7% was the magical figure IIRC). In other words, a very slight amoung of slip (understeer, oversteer, 4w drift, depending on the corner) was always faster than no slip at all. Anything more than this, and the grip levels fell away quite quickly (and obviously increased wear and tyre overheating)

Even on gravel, the best drivers admit that straight is fastest. It's just so boring - that's why so many of us choose the (slower) RWD option in gravel rallying - we do it for the rock chucking goodness, not to win trophies.

bah, watch and learn...

OK, so Brocky was a little looser than ideal in a couple of spots, but if you want to squeeze every last tenth out of it for a single fastest lap, you have to walk that line. The very start of the video is what sums it up best for me; Brocky coming onto the pit straight with the car looking nice and smooth, yet the driver sawing at the wheel - perfectly on the edge!

Awesome video. I see what you're saying. :P

bah, watch and learn...

OK, so Brocky was a little looser than ideal in a couple of spots, but if you want to squeeze every last tenth out of it for a single fastest lap, you have to walk that line. The very start of the video is what sums it up best for me; Brocky coming onto the pit straight with the car looking nice and smooth, yet the driver sawing at the wheel - perfectly on the edge!

Yeh, great vids of the old Grp A cars....but i will add that Perkins had his race engine in and Brock had a practice engine in. Brock was slower to the chase then Larry so in the handling stakes Larry pasted Brock up and over the Mountain...Brock made all the time up down Conrod. So for Brock to pull back all the time on Larry, Larry running his race engine etc...he was obviously giving away a fair wack of straight ahead to the 05 car. So that tells me that the smoother line of Larry was quicker

practice and race engines were the same spec, the race engine would be a fresh one for the 1000km race, vs Brock's well used practice engine... I doubt that was a disadvantage for Perkins! In fact Perkins top speed on Conrod was 277.9, Brocky 277.8 so how can you suggest Brock made up all his time down Conrod???

split time at Forest Elbow was a 1:30 for Brock and they originally said 30.9 for Perkins, but there was some confusion over it and they changed their minds to a 30 as well, probably because they were so convinced his smoother lap was going to be faster as they had been saying all the way through it. Maybe they just didn't want to be proven wrong on national television...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...