Jump to content
SAU Community

Recommended Posts

Scott fitted the Brembo brake package for me today, pretty much a bolt on affair with the calipers...used an angle grinder to hack off the dust shield in the rear.

350z Brembo calipers (F&R)

RDA slotted rotors

HPX pads

Stoptech G35 braided lines

the front braided lines had to be fiddled around with in order to get them fitted correctly and not hit/rub/scrub against the wheel. The rear lines fitted fine.

Bled the brakes and refilled with Nulan DOT4 fluid.

The Good: looks nice...brakes seems much grabbier when engaged.

The bad: brake travel shot to hell. In order to engage the brakes I had to depressed them fully or pump them. Scott thinks either a bigger master cylinder is needed, or a rebleed is needed.

Made an interesting drive down to Portsea tonight. Was pretty scared I was gonna stack...

post-75595-0-05707000-1304776115_thumb.jpg

post-75595-0-52610900-1304776164_thumb.jpg

post-75595-0-15311100-1304776237_thumb.jpg

post-75595-0-74784000-1304776387_thumb.jpg

Edited by ironpaw
  • Replies 129
  • Created
  • Last Reply

Top Posters In This Topic

Gets shorter. After a few pumps the brakes feel good.

As Duncan said...more than likely ableeding issue....I had issue's bleeding mine when I put em on as well. Took it for a test run with and on the second big hit they were fine.

I had no issues bleeding mine, these are a weird setup as the callipers run twin bleeders. Is there a particular method I should be using on the Brembos? We flushed the whole system and I bled each nipple until there was no bubbles, starting with the inside ones. Then I did them all again to make sure. Perhaps there was an air lock somewhere?

Hopefully any excess air has worked its way into the callipers, I will re-bleed the system for you tomorrow if you like.

your also supposed to either disconnect the battery or unplug the abs module

if you got any air in the abs you may also need to cycle it too (something that is done from the nissan diagnostic thingo)

if you got any air in the abs you may also need to cycle it too (something that is done from the nissan diagnostic thingo)

craigs 'big hit' may have moved some of the bubbles from the ABS module to the caliper.

ironpaw, keep an eye on the front brake lines. one of mine moved and rubbed on the front driveshaft and started wearing out the braiding. so maybe double the cable ties

Scott rebled the brakes. Got a a couple more bubbles out. Pedal travel is pretty much similar to stock now...which is better but I'd think with all the stuff I installed the brake travel would be much less...

hmmm maybe I need to take a big hit with it...LOL

Scott rebled the brakes. Got a a couple more bubbles out. Pedal travel is pretty much similar to stock now...which is better but I'd think with all the stuff I installed the brake travel would be much less...

hmmm maybe I need to take a big hit with it...LOL

maybe a new master cylinder?

It's the total area that the master cylinder has to move that might make a longer pedal. Single piston calipers tend to have very large pistons. Best way to tell if the master cylinder is not OK is to measure the standard and new pistons and see how much larger the new ones are. Often the difference is minimal because it is the calipers that are larger not the pistons inside them.

And basically, bleeding after replacing everything can be a real PITA. Sometimes it is OK straight away, sometimes it will need a few shots.

A properly bled braking system should have a short pedal travel to get the pads to the disc, and then be consistent pressure all the way to the bottom. You should get the same feel on every push.

If it gets better after a pump or 2 you probably still have air in the system. If you get to the bottom and it sinks slowly you have a leak somewhere. If it is consistently long you have bled it OK and may need a larger master cylinder

maybe a new master cylinder?

nah......my peddle is perfect....doesn't need a new master cylinder.....if it's still soggy you still have air in the lines.....did you do rears as well? If not have you ever bleed the rear?

nah......my peddle is perfect....doesn't need a new master cylinder.....if it's still soggy you still have air in the lines.....did you do rears as well? If not have you ever bleed the rear?

Scott rebled all four brakes.

Its better now but if I pump it the peddle feel gets better.

Found out on 350z forums that the master cylinder between brembo and non brembo 350z's are the same: http://www.350z-tech...ap-brakesmg.jpg

The difference is the brake booster?

is it even possible to replace the brake booster?

Danny said he never replaced his master cylinder but he didn't mention whether his peddle travel improved either....

found this: http://cgi.ebay.com/ebaymotors/06-Nissan-350Z-PWR-Brake-Booster-Master-Cylinder-R4376-_W0QQcmdZViewItemQQhashZitem43a4829cc4QQitemZ290522832068QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories

Edited by ironpaw

Scott rebled all four brakes.

Its better now but if I pump it the peddle feel gets better.

Found out on 350z forums that the master cylinder between brembo and non brembo 350z's are the same: http://www.350z-tech...ap-brakesmg.jpg

The difference is the brake booster?

is it even possible to replace the brake booster?

Danny said he never replaced his master cylinder but he didn't mention whether his peddle travel improved either....

found this: http://cgi.ebay.com/...sQ5fAccessories

I am pretty sure Chris(Akebono) and Ben(Brembo) have not replaced there master cylinder or brake booster either.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
    • I assume clearances were all a-okay?
×
×
  • Create New...