Jump to content
SAU Community

Recommended Posts

I've been considering getting the HID R33 headlights, but they go for a pretty penny here in Japan. found some new in the box for 1600 USD. not worth it at all. that's my Tomei Oil Pump, or something else useable.

Since I'm typing- updates today. Replaced starter, old one said goodbye over the weekend filming that video. That is the most pain in the ass starter I've ever had to replace, took me over 2 hours of pleading with god to get the top bolt off. Also removed the sound deadening that was cemented to the floor pans and such. On the prowl for a roll cage, interior sprucing up after that.

pffft wow! no shit that looks tuff with the new wheels 30profile thats brave ahah, love that last photo too!

Thanks mate. These are probably going to be my cruising wheel/tire combo, as it's a terrible set up for the track. probably will opt for the more standard 18"/35 series on the track.

Oh.... that last photo made me all tingly inside (DOF shot)... Hires plz? :)

here ya go, it's 28 megapixels though.

4754245171_9fe42206ca_o.jpg

also, completely removed the sound deadening that is cemented to the floor panels. Use a pneumatic chisel and bulldozed it in just over an hour. Screw the fancy dry ice shit. haha, this way cost me free 99. And to celebrate here's a weight update.

Weight update...

Removed rear seat and rear seat safety belts for 31 pound/14.1kg reduction.

Stock Trunk Carpeting - 11.5lbs/5.2kg

Stock Floor Mats - 13.0lbs/5.9kg!!

Stock Jack/Tire Iron - 4.5lbs/2.05kg

Stock Spare Tire - 34.4LBSSSS/15.6kg

Nissan Air Purifier,sound deadening behind back seat, car jack - 9 lbs/4.1kg

metal plate behind the back seat - 6.4 pounds/2.9kg

Stock suspension 57.8lbs/26.3kg and HKS Hipermax 47.0/32.3kg - 10.8lbs/6kg net loss

door panels 14lbs/6.35kg

carpet and various pieces of plastic 16.2/7.3kg

Center console 7.6lbs/3.5kg

passenger seat 34lbs/15.4kg (with rail attached)

Difference in test pipe/cat 6lbs/2.7kg

new seat/rail vs old seat/rail 5lbs/2.3kg

dash stripped to shell - 3lbs/1.36kg

difference in exhausts 24.2lbs/11kg

all sound deadening 12lbs/5.5kg

=

242.6 pounds/110.3kgs

Stock R33 GT-R 3388lbs/1540kg

so I'm at 3145.4lbs/1429.7kgs. Still heavy! Still to come out. Rear windshield wiper assembly, HICAS, switch to CF Driveshaft, stock exaust manis, outlet pipes and downpipes.. to be replaced with SS and titanium respectively, and more!

Ive been going through this thread and im frickin loving the work mate,thats real talent.It'l be the ultimate test for a permanent marker lol

Just imagine if it was in fluoro sharpie haha thatd be sick.

rb30 huh? OS Giken sells an rb315 kit to up your 26 displacement to 3.15L

http://www.osgiken.co.jp/pro_spec/rb30kit.html

Nice work btw; love this thread.

sounds cool, but for almost 20,000 USD, I can buy an insane engine already done up vice the OS Giken stroker kit :D

I'd like to thank Fast Car Magazine! Maybe when the car is done, they will be interested in a bigger spread!

DSC_3683.jpg

DSC_3685.jpg

Build is on hiatus until after I purchase Allison an engagement ring. Shhhhhh!

polished the headlights, and removed the A/C radiator/fan. compressor is next but i didnt go to the garage today.

DSC_3696.jpg

DSC_3701.jpg

DSC_3708.jpg

DSC_3711.jpg

the radiator and fan weighed 15lbs/6.8kgs

Weight update...

Removed rear seat and rear seat safety belts for 31 pound/14.1kg reduction.

Stock Trunk Carpeting - 11.5lbs/5.2kg

Stock Floor Mats - 13.0lbs/5.9kg!!

Stock Jack/Tire Iron - 4.5lbs/2.05kg

Stock Spare Tire - 34.4LBSSSS/15.6kg

Nissan Air Purifier,sound deadening behind back seat, car jack - 9 lbs/4.1kg

metal plate behind the back seat - 6.4 pounds/2.9kg

Stock suspension 57.8lbs/26.3kg and HKS Hipermax 47.0/32.3kg - 10.8lbs/6kg net loss

door panels 14lbs/6.35kg

carpet and various pieces of plastic 16.2/7.3kg

Center console 7.6lbs/3.5kg

passenger seat 34lbs/15.4kg (with rail attached)

Difference in test pipe/cat 6lbs/2.7kg

new seat/rail vs old seat/rail 5lbs/2.3kg

dash stripped to shell - 3lbs/1.36kg

difference in exhausts 24.2lbs/11kg

all sound deadening 12lbs/5.5kg

radiator and fan 15lbs/6.8kgs

=

249.4 pounds/117.1kgs

Stock R33 GT-R 3388lbs/1540kg

Lost Birds R33 3130.4lbs/1422.9kgs.

Edited by istdercollen

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...