Jump to content
SAU Community

Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Godzilla Motorsport wishes you all the best on your endevour to beat theos 8.95 time...

regards, mark

Thanks Mark, we have always had the H pattern record in our sights...even if we don't go that quick to have a good meet and manage a PB with consistent runs backing it up would be a success.

I still haven't recieved the Quantum and Speedflow invoices as earlier requested, please forward them to my email account so i can transfer you the cash.

good luck in your future racing and the crack at the 7.56.

Yummo!

Car smells like thinners now though.

Given the high standard of Taryn's cullinary talents she could make the guniea p1g the neighbours dog was proudly marching around with in its mouth this afternoon taste a treat!

Id say someone in the street would have had some quite upset children returning home from school this afternoon.

Edited by Swiper the Fox
  • 3 weeks later...

sorry guys only just got internet access...

the small crack in the block that was repaired last time engine was freshened has opened up weeping coolant out. In the interests of my own and others safety i decided not to run the car. Looking back i probably should have grouted the block as the crack is below the bottom of the welsh plugs and grouting would have stopped it.

Its very strange as when the car was rolled back on Friday no coolant was leaking out of it. A little later i jacked the front of the car up in preparation for welding a lambda sensor bung at the base of the dump pipe and coolant started to drip from the rear of the engine. We stripped the engine on Friday night and tried to repair it but on Saturday morning started leaking again. Engine is now out and ill decide tomorrow if ill just grout it or replace the block with a fresh one.

Very disapointing for all involved with the car.

Edited by Swiper the Fox
Unfortunate you couldn't make it today.

Is the car going to be heading back to the track at some point after repair ?...or will it now be taken out of action for good .

oh no we dont give in that easily...unfinished business needs to be attended to.

the car has never been set-up properly for drag racing until now...i couldn't live with the massive 'what if' by not running it again.

oh no we dont give in that easily...unfinished business needs to be attended to.

the car has never been set-up properly for drag racing until now...i couldn't live with the massive 'what if' by not running it again.

good to hear you're gonna give a hard nudge & get that 8sec 1/4 :unsure:

do u know what date you're heading out as yet?

Hey Paul i tried to call you today but your phone was off.

Were gonna organise a private test day for about 3 weeks so i will let you know

Cheers

Paul

hopefully they will give us a better track than last time

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Factory Dash Lamps...Half the speedo was dark...T10 3 Watt Park Lamps...T10 5 Watt Tachometer Chip/IC...Tach would randomly go crazy or stop, replacing  capacitors and re-soldering the chip would work for a week or so but it would always fail again...AN8352UBK (Buy on ebay AU) Heater/Air Con Control Button Lamps...Grain of Wheat Bulb 12V...Tried LED's they fail after a month or so(even with current limiting resistors)
    • Hi, need help on wiring i swap motor from rb25de neo to S1 rb25det. Is it possible i can still use the de neo loom or do i need the s1 loom? Can i add extra wiring to add wastegate soleniod and iat sensor? Can i use injector and coils on same loom as i running bosch injectors and vag coils? I bought nz wiring trigger kit for neo, can i use that on s1 motor? What else do i need to do to work everything right?
    • Tried some stainless allen head bolts I had laying around, they stuck out like dog balls, so I went to Bunnings and got some black coated jobbies, which I like alot more.....basically OEM....LOL I'll RTV it up this week sometime ready for MX5 Mania to do their thing
    • Good tips, will get on those tomorrow. When doing the maintenance I did move a few of those connectors around, and things that are old tend to not like moving around. (Like me).
    • Don't try it. It will be shit. Better chance of damaging the engine than gaining any knowledge about the old one. Maybe, but unlikely, especially if the O2 sensor is working. You can use NissDataScan to look at the stock ECU.   Cleaning the AFM is seldom necessary and seldom helps. The R35 coil & loom conversion should eliminate dud coils or plugs. But as you still have misses - look to the plug where the coil loom connects to the engine loom, and the CAS plug. Need quality connections there. Also look to injector plugs. And the AFM plug while you're at it. Also look to whether your injectors are clean and flowing evenly. Get them out and onto a testbench.
×
×
  • Create New...