Jump to content
SAU Community

Recommended Posts

hey all, im about to start an RB30 twincam conversion on my stagea, need some advice on who are the best people for the job. ill be doing all the engine removing/refitting myself, just need someone to modify my NEO head and do one last mod on my 30 block, then bolt it together. i bought a RIPS 4wd RB30 block, its all set up for the conversion except for an oil supply to run VCT because id like to keep it active.

so that and the head mods and they need to be able to tune it for me when ive got it all back together... car is 4wd which narrows down dynos in the area but if the shop is good enough and only has 2wd dyno, i can make it run in 2wd.

so who do people recommend? i know esp do good work but ive also been told they charge alot for it. at the end of the day, im not rich but i dont want a shit job either.

D.

Link to comment
https://www.sau.com.au/forums/topic/310778-workshop-advice-needed/
Share on other sites

+1 for Pro Engines.

I think you'll find that ESP and Autotech (def Autotech anyway) will use Pro Engines for the head work and any mods there anyways.

In terms of tune just talk to the workshops and pick somewhere that you're comfortable with. There's good and bad stories everywhere.

not really, heard they still did a bit of work from home but now one of the guys, phil, has moved to bathurst so i doubt they're still doing anything. while we're on them, the main guy (name evades me) has a very very nice r32gtr... tidy and subtle. still has skylines performance on the number plate too...

pro engines sounds like the go at the moment, checked out the website and they make RB30 awd adaptors so i guess they know what they're on about. will get in contact with them and see how we go.

anyone else anyone can think of??

D.

Edited by pintaline
how much $$$ (at least) they charged for complete engine swap in canberra? just in general without any fancy headwork etc.

my 25de is dying and i got 25det neo ready to slap asap.

thanks.

Want to sell that dying 25de?

Edited by StinkyPoo

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...