Jump to content
SAU Community

Recommended Posts

yeh thats what i saw when i looked

18x9.5 +20 rota grids

with a 20mm spacer on front its now 18x9.5 +/-0

and a 15mm spacer on rear its now 18x9.5 +5

NT033.jpg

VoltexEvo8.jpg

ewww both these cars are running voltex widebodies, the rear quarter bolt on sections are shit as

:P this is the wastelandz you idjit. thread only ends when it get too big (approx 1000pgs) and funky makes a new one

i knooooooooooooooooooooo

miss the point much :)

yeh the te's are huge im diggin the bbs if u rock that stance though if u dont slam it like that will llook pox

why would u bother ? if u want stilts get some 4x2 from bunnings haha..

nah do it once do it right go baller cos most evo's fail that i see

haha they do, most run about what ive got now 8.5 +35 or 8 +38

the 9 +17 wil be a near perfect fit any wider/lower offset itll rub bad and i dont wana flare

get some adjustable coilovers and rise it higher, and then use it for what it was meant for and find some dirt tracks for some rally goodness :) .

i live on a dirt road, but i hate driving on it

i like clean cars, ive taken it down the road once it was soooo filthy afterwoods and dust was in everything.... never again

now snow.... thats a different story..... common winter :P

i live on a dirt road, but i hate driving on it

i like clean cars, ive taken it down the road once it was soooo filthy afterwoods and dust was in everything.... never again

now snow.... thats a different story..... common winter :)

im the same, i hate hearing the stones flick up and you hear them hitting your car, it makes me cry.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
    • Bloody apprentices! 🙄
×
×
  • Create New...