Jump to content
SAU Community

Recommended Posts

yeh thats what i saw when i looked

18x9.5 +20 rota grids

with a 20mm spacer on front its now 18x9.5 +/-0

and a 15mm spacer on rear its now 18x9.5 +5

NT033.jpg

VoltexEvo8.jpg

ewww both these cars are running voltex widebodies, the rear quarter bolt on sections are shit as

:P this is the wastelandz you idjit. thread only ends when it get too big (approx 1000pgs) and funky makes a new one

i knooooooooooooooooooooo

miss the point much :)

yeh the te's are huge im diggin the bbs if u rock that stance though if u dont slam it like that will llook pox

why would u bother ? if u want stilts get some 4x2 from bunnings haha..

nah do it once do it right go baller cos most evo's fail that i see

haha they do, most run about what ive got now 8.5 +35 or 8 +38

the 9 +17 wil be a near perfect fit any wider/lower offset itll rub bad and i dont wana flare

get some adjustable coilovers and rise it higher, and then use it for what it was meant for and find some dirt tracks for some rally goodness :) .

i live on a dirt road, but i hate driving on it

i like clean cars, ive taken it down the road once it was soooo filthy afterwoods and dust was in everything.... never again

now snow.... thats a different story..... common winter :P

i live on a dirt road, but i hate driving on it

i like clean cars, ive taken it down the road once it was soooo filthy afterwoods and dust was in everything.... never again

now snow.... thats a different story..... common winter :)

im the same, i hate hearing the stones flick up and you hear them hitting your car, it makes me cry.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Brooooo Please send ABS control unit schematic Please! R33 gts25t ABS (Its two plug ecu, black and white) wire colors possible? [email protected]
    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
×
×
  • Create New...