Jump to content
SAU Community

Vic Wasteland Thread

paulr33

By paulr33,
in Victoria

 Share

Recommended Posts

  • Replies 26.6k
  • Created
  • Last Reply

Top Posters In This Topic

  • Mohsen

    2235

  • funkymonkey

    2055

  • alr33x

    1692

  • dezz

    1469

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

VSPECT
VSPECT

who cares....ill stand to what i said...IPHONES ARE GAY!!! GALAXY FTW!!!!!!!!!

VSPECT
VSPECT

iphones gay....

krzysiu
krzysiu

Aww grant. Says your rep is poor now! I'm on +1 haha *waits for everyone to give this post negative rep*

Posted Images

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

It's boring ey

Yes and tune that aren't that good doesn't help either.

Flat spots between 5-6,000rpm so would need to look at tune or EBC settings.

Still cbf trying to take some photos of it to sell it.

Count Grantleyish Grand Master

Count Grantleyish

Posted
Posted

Someone from country Vic wants to look at my Skyline in a couple of weekends time. Sounds positive. I hope they buy it :)

Best of luck.

And how did the parting of the Pulsar went?

llama_au Grand Master

llama_au

Posted
Posted

Best of luck.

And how did the parting of the Pulsar went?

Thanks. I reduced the price again I think that's where the renewed interest has come from.

Parting the Pulsar is going good so far; the coilovers, EDFC and the whole interior went last weekend. Most performance/cosmetic parts come off this weekend and I've received deposits for them. Engine and gearbox don't have buyers yet but I assume once they're out they'll be easier to sell. Then in a few weekends time an N/A engine and gearbox go in the car, I'll get a few bits painted and tidied up and I'll sell the whole working car as an N/A SR which should interest the younger market as it'll be a quick N/A car with nice paint, kit, etc. Easier to sell it this way.

UNR33L Grand Master

UNR33L

Posted
Posted

Question for Alex / Billy:

Have you got any pics of your exhaust like underneath? thinking about going dual tips a bit like you guys cos it looks bad ass from the Tuesday meet pics, and also the other reason is so I can lower it a bit more without this HKS thing almost hitting the ground it hangs so low. Any info would be good cheers :)

d7000-1413.jpg

d7000-1420.jpg

:cheers:

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...