Jump to content
SAU Community

Recommended Posts

paul. i slipped it into 1st instead of 3rd

u managed to go from 4th gear to 1st gear by accident? Unless you managed to rev-match i find that hard to believe. Unless you were rolling at 10kmh in 4th gear and then went into 1st haha

http://www.youtube.com/watch?v=avU5onrWfYo

whats the bbcode to embed youtube on these forums?

[/video ]

okay, i didnt slip it, i smashed it, thinking it was going to go into 3rd... it made an awful grinding noise. but as soon as i realised, slipped it back into neutral.

haha the whole truth comes out, cant half truth it here :D

You still interested in doing Industrial Design.

My brother applied for monash ind Design and his friend applied for rmit ind Design.

Monash included a portfolio submission and an interview

rmit included a test which i think leads to an interview.

oh and...

yeah boyeeeeeee...

Cummins-Rat-Rod.jpg

Cummins-RatRod.jpg

fark yehhhhhhhhhh tufffff

okay, i didnt slip it, i smashed it, thinking it was going to go into 3rd... it made an awful grinding noise. but as soon as i realised, slipped it back into neutral.

shit kent :D

[/video ]

haha the whole truth comes out, cant half truth it here :cool:

You still interested in doing Industrial Design.

My brother applied for monash ind Design and his friend applied for rmit ind Design.

Monash included a portfolio submission and an interview

rmit included a test which i think leads to an interview.

yep, sure am.

im thinking about doing it at swinbourne..

Rmit= test= f**k that

this years my last year of school... FUUCKKKKKKK YEAHHH!!! :(

oh and nick, twas the first lesson man! i has improved!

also: thinking about buying personalised plates to show how passionate i am to some of my sydney born mates

[sYDSUX] :)

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...