Jump to content
SAU Community

Recommended Posts

I've got I've got some 225/45 R18 Bridgestone Potenza RE040 on my AXIS wheels at the moment.

They are getting a bit worn, so I'm after some recommendations.

From reading some old threads it seems that I can either go for more 225/45 R18 tyres, or swap to 235/40 R18 which may give me more options.

I'm looking for something that's good in the wet, and ideally sub $300 a corner.

I've got no brand loyalty, so recommend away.

Thanks

Link to comment
https://www.sau.com.au/forums/topic/312401-tyre-recommendations-for-r18-axis/
Share on other sites

225/45/18 and 235/40/18 will not give the same speedo reading.

With 235/40/18, the speedo will read around 3-4% higher than the 225/45/18

The 225/45/18 is a recommended replacement for the stock RS 17's as it does not upset the speedo.

I am running 235/45/18 on my RS and I can tell you that my speedo reads a little high.

Will be switching to the 225/45's as a correctly reading speedo is a nice thing to have and the extra 10mm over the 230/40 will fill out the guards nicely :P

I've got Toyo Proxes4 all round, 235/40/R18 fronts, 245/40/18 rears, probably best for their prices IMO.

I am running 245/40 18's on my AXIS. The rolling stock diameter of the tyres is within the suggested 3% variance. .its actually very close

I have the Proxes 4 tyres from Toyo and they are the best tyres I have has thus far. . $1,080 fitted for all 4, so $270 each.

The toyo's have a high load rating 97w . . which were one of the highest for that class of tyre. and needed for the 1.8 tonne wagon.

225/45/18 and 235/40/18 will not give the same speedo reading.

With 235/40/18, the speedo will read around 3-4% higher than the 225/45/18

The 225/45/18 is a recommended replacement for the stock RS 17's as it does not upset the speedo.

I am running 235/45/18 on my RS and I can tell you that my speedo reads a little high.

Will be switching to the 225/45's as a correctly reading speedo is a nice thing to have and the extra 10mm over the 230/40 will fill out the guards nicely :D

I have Khumo HR31's on mine, 245/45/18 on ARX wheels, this is quite a jump over std RS 17" rolling dia, but on a gps, my speedo is only out by about 3% as opposed to 9% :blush: with the std wheels and tyres.

The larger rolling diameter hasn't blunted the performance by much, but the ride is muuuuch better than before, even though the aspect ratio of the tyre is smaller and the extra rubber gives a much larger footprint. The extra width will still fit easily under the guards. They are also a nice quiet tyre with astounding amounts of wet weather grip. Also wearing quite nicely after 6000km.

Cheers, Dale

I have Khumo HR31's on mine, 245/45/18 on ARX wheels, this is quite a jump over std RS 17" rolling dia, but on a gps, my speedo is only out by about 3% as opposed to 9% :blush: with the std wheels and tyres.

The larger rolling diameter hasn't blunted the performance by much, but the ride is muuuuch better than before, even though the aspect ratio of the tyre is smaller and the extra rubber gives a much larger footprint. The extra width will still fit easily under the guards. They are also a nice quiet tyre with astounding amounts of wet weather grip. Also wearing quite nicely after 6000km.

Cheers, Dale

interesting.... may have to break out the GPS and give it a little look-see

Bit of a boo boo in my original post. Khumo's are KU 31, not HR 31.

Cost $290 per tyre in 245/45/18 although should be cheaper now, as this size is std equipment on VE 18's and also current falcon 18's.

My speedo is way out already with the current setup. I think it reads about 10% fast vs my tomtom.

A smaller aspect should somewhat address that right? Smaller diameter should give more revolutions for equivalent distance travelled?

Thanks for the recommendations as well. Gives a more focused list to hunt prices on.

My speedo is way out already with the current setup. I think it reads about 10% fast vs my tomtom.

A smaller aspect should somewhat address that right? Smaller diameter should give more revolutions for equivalent distance travelled?

Thanks for the recommendations as well. Gives a more focused list to hunt prices on.

I *think* it should be the other way around - I went from the standard C34 Stagea wheels with 225/50R16s to 245/40R18s and my speedo is much more accurate now, despite the larger rolling diameter...

interesting.... may have to break out the GPS and give it a little look-see

So I took the GPS to check how far out my speedo is on the way down to watching the "Classics" at Phillip Island yesterday.

Since I have upgraded my wheels and using the 235/40/18's that came with, my speedo is 10-11% out (reading higher than actually travelling).

Looks like a good excuse to get fatter tyres next time :(

  • 4 months later...
I am running 245/40 18's on my AXIS. The rolling stock diameter of the tyres is within the suggested 3% variance. .its actually very close

I have the Proxes 4 tyres from Toyo and they are the best tyres I have has thus far. . $1,080 fitted for all 4, so $270 each.

The toyo's have a high load rating 97w . . which were one of the highest for that class of tyre. and needed for the 1.8 tonne wagon.

  • Could someone indicate which measurement must be within the 3% variance , in the quoted post?
  • Is the rim width on the M35 Axis Autech 7.5inch or larger ?
  • I need to know what tyre size will be acceptable when I go through compliance as I wont be around when it happens .
  • Has anyone tried the Toyo Teo plus for 235 40 18?
  • What new recommendations to Axis owners have for replacing the standard size 225 45 18 tyre or are you content with
    that size
  • What normal profile choice do I have if i don't proceed with a low profile tyre?

Thanks in advance

  • Could someone indicate which measurement must be within the 3% variance , in the quoted post?
  • Is the rim width on the M35 Axis Autech 7.5inch or larger ?
  • I need to know what tyre size will be acceptable when I go through compliance as I wont be around when it happens .
  • Has anyone tried the Toyo Teo plus for 235 40 18?
  • What new recommendations to Axis owners have for replacing the standard size 225 45 18 tyre or are you content with
    that size
  • What normal profile choice do I have if i don't proceed with a low profile tyre?

Thanks in advance

The 3% variance is for variation in tyre from O.E. I would guess.

The Axis rim is 18x8" +30 offset. It will easily take a 245 wide tyre without looking too "muffin top" :D .

As per my previous post; a 245/45/18 gives a slightly larger rolling diameter, and tested against a GPS, reduced speedo error from 110 km/h at a GPS verified 99 km/h, to 110 km/h at a GPS verified 107 km/h.

Khumo KU31 in the 245/45/18 has a load rating of 100.

Hope this helps, Dale

  • Could someone indicate which measurement must be within the 3% variance , in the quoted post?
  • Is the rim width on the M35 Axis Autech 7.5inch or larger ?
  • I need to know what tyre size will be acceptable when I go through compliance as I wont be around when it happens .
  • Has anyone tried the Toyo Teo plus for 235 40 18?
  • What new recommendations to Axis owners have for replacing the standard size 225 45 18 tyre or are you content with
    that size
  • What normal profile choice do I have if i don't proceed with a low profile tyre?

Thanks in advance

Hello,

It's the RSD Rolling Stock Diameter that needs to be within the 3% variance as it messes with the speedo.

Check here for all your requirements

http://www.1010tires.com/tiresizecalculator.asp

I swear by the Proxes 4, be sure what ever tyre you get has the appropriate load rating (eg 97w) as larger cars need a higher load rating, simply because they weigh more and is particularly important in heavy performance cars. I found many tyres had the right size but failed the load rating requirement.

I love the 245/40/18 97w profiles I have now and will not change. .

Remember the wider your tyre is, the side wall measurement changes in proportionate ratios. Which means a thinner tyre say 225/40 side wall will be a completely different size to a 245/40 side wall. It's all about relative ratio to tyre width.

Julius

Edited by Paramour
Hello,

It's the RSD Rolling Stock Diameter that needs to be within the 3% variance as it messes with the speedo.

Check here for all your requirements

http://www.1010tires.com/tiresizecalculator.asp

I swear by the Proxes 4, be sure what ever tyre you get has the appropriate load rating (eg 97w) as larger cars need a higher load rating, simply because they weigh more and is particularly important in heavy performance cars. I found many tyres had the right size but failed the load rating requirement.

I love the 245/40/18 97w profiles I have now and will not change. .

Remember the wider your tyre is, the side wall measurement changes in proportionate ratios. Which means a thinner tyre say 225/40 side wall will be a completely different size to a 245/40 side wall. It's all about relative ratio to tyre width.

Julius

Hello julius .

Thanks for the advice .

The japanese web site has 91 w for the stagea Axis autech http://www.autech.co.jp/HISTORY-SV/M35S01/eq.html if I decipher it correctly.

Where does your 97w come from as I cant locate any 225 45 18 tyres with a 97w rating

you in brissy mate

get your tyres from www.option1garage.com.au

very cheap

http://www.option1garage.com.au/NewTyres.htm

i think the ku31's were under $200 a corner

acutally, i found this, i asked for a quote a while ago

Kumho

235/40/18

KU31 $156.00

KU27 $192.00

KU37 $157.00

you in brissy mate

get your tyres from www.option1garage.com.au

very cheap

http://www.option1garage.com.au/NewTyres.htm

i think the ku31's were under $200 a corner

acutally, i found this, i asked for a quote a while ago

Kumho

235/40/18

KU31 $156.00

KU27 $192.00

KU37 $157.00

Yes in Brissy mate.

Comments I have received seem to rate the falken 452just over the federal over the KU31.

Is that a fair commment.

I have usually run Potenza but just not economical at the prices they are sellinfg at .So now I am trading off safety a little bit for mileage .I was very disappointed with michellan Pilot precedes as they wore out real quick

Edited by samuri

send option1 an email and tell them what your looking for

they will recommend you a tyre and unless you can order from a wholesaler they will be cheaper that bob jane or other tyre places

they sell more than what they advertise, could be worth just going to see them

the ku36's are supposed to be a good semi-slick (beter than the federal rs-r's) but probably not what your after

don't really know much about any of the other tyres but i'll find out once i have some money for new wheels too

let us know how you go, where you went and how much it was tho

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...