Jump to content
SAU Community

Recommended Posts

i have seen dyno sheets floating around which are probably in this post somewhere anyway - which show the difference in the response between, 6266, 6466,6766 being about 500rpm on a 3.4L ...

I have even emailed precision directly who have confirmed that it would be about 300-500rpm on a 3L

Thanks. Have seen it but not sure on that one. I think the 6262 is the one.

Thanks. Have seen it but not sure on that one. I think the 6262 is the one.

Yeah just give it a ago they are pretty interchangable apparently.

I went for the 6466 as I figure if worst case it was 600-700 difference in response from the 62-64 - something i doubt im really going to notice when its on an engine which will snap the rpm needle within a matter of seconds anyway - which is worth it considering the top end gains!

  • 2 weeks later...

Is anyone running a 6266? How much lag are we talking about between the 6262 and the 6266? Can't decide on what to go for. If the RPM difference is negligble i'd be more inclined to go with the 6266 for the potential to make more power at a later date. (Both turbos with 0.84 Twin scroll)

Looking to make 400kw on a RB26 with all the basic mods. Will a 6262 make that power on 98pump fuel (say no more than 25psi)? I've seen that SimonR32 made 420 but that was on flexfuel.

Edited by RRP1

I actually made 450kw and trust me there is plenty more in it but I ran out of fuel pump.

I wouldnt be suprised to see another 30-40kw if I ran 25psi but as you said that is on e85.

6262 is a nice balance for decent power and not too much lag. I was tossing up between it and the 6266 and went the smaller. I think I made the right decision

Edited by SimonR32

no probs....i dont think there will be too much difference to be honest but i cant find the wheel sizes for the 6266

6262 is as below tho

Compressor-

Wheel Inducer: 62mm

Wheel Exducer: 82mm

Turbine Wheel -

Wheel Inducer: 72mm

Wheel Exducer: 62mm

i think i did read that the exducer of the 66 was slightly bigger but dont quote me

PTE 6466 - for anyone looking at this turbo.

Compressor Wheel 2.535" (64.39mm) inducer / 3.410" (86.61mm) exducer

Turbine Wheel 2.920" (74.17mm) inducer / 2.600" (66.00mm) exduce

HKS T04Z:

Compressor Wheel:

T04R/T04Z, Inducer 66.7mm, Exducer 84mm.

Turbine:

T04 P trim, Inducer 74.2mm, Exducer 64.6mm

Garrett GT3540R/GT3582R/GT35R:

Compressor Wheel:

56 trim GT40, Inducer 61.2mm, Exducer 82mm.

Turbine:

84 trim GT35, Inducer 68mm, Exducer 62mm,

for comparison..

Alot of guys are running the 6466 in favour of the 6266 in the states and report no change in spool/response but more power up top.. Would like to see some results on RB26 though.

Edited by RRP1

So how do people reckon a PT6466 would compare with a Garrett T04Z in overall performance? Would you be able to use the Precision in the Garrett's place and expect to make similar (or better) power on pump gas on a suitably built engine?

PTE 6466 - for anyone looking at this turbo.

Compressor Wheel 2.535" (64.39mm) inducer / 3.410" (86.61mm) exducer

Turbine Wheel 2.920" (74.17mm) inducer / 2.600" (66.00mm) exduce

HKS T04Z:

Compressor Wheel:

T04R/T04Z, Inducer 66.7mm, Exducer 84mm.

Turbine:

T04 P trim, Inducer 74.2mm, Exducer 64.6mm

Garrett GT3540R/GT3582R/GT35R:

Compressor Wheel:

56 trim GT40, Inducer 61.2mm, Exducer 82mm.

Turbine:

84 trim GT35, Inducer 68mm, Exducer 62mm,

for comparison..

Alot of guys are running the 6466 in favour of the 6266 in the states and report no change in spool/response but more power up top.. Would like to see some results on RB26 though.

6466 only comes in ball bearing tho which is all good but cant justify the extra cash for it

So how do people reckon a PT6466 would compare with a Garrett T04Z in overall performance? Would you be able to use the Precision in the Garrett's place and expect to make similar (or better) power on pump gas on a suitably built engine?

i dont think you can go wrong the PTE to be honest

So how do people reckon a PT6466 would compare with a Garrett T04Z in overall performance? Would you be able to use the Precision in the Garrett's place and expect to make similar (or better) power on pump gas on a suitably built engine?

Should make plenty more power without being too much laggier from what I have seen

Thats interesting, I'd have hoped for it to be at least as responsive!

Well my 6262 is better than my old T04Z but not the miracle that some would lead you to believe. The 6466 is a fair wack bigger (195hp rated), I doubt you would be getting that for nothing :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...