Jump to content
SAU Community

Recommended Posts

Well i'm off to the EC sprint on the 18th too, so no excuses about being rusty! Will have to think of another excuse before then...

I'm taking a mate out as a passenger at this Wakefield day too, so better be on my best beahviour. :D

Yeah next round of SSCC @ E/C!!! I am heading back past from the Blue Mountains on the Sunday and thinking of coming in and seeing how everyone is going, not sure if the missus will agree though :D

Rusty!??? Mate you will be ace! No stress required, with all your little tweaks and hopefully alignment sorted = FLYING!!! Dont show the car fear, show it who's boss!!! :woot:

Hopefully you can knock a few seconds off both your E/C & Wakey times!!!

Just keep ahead of Stu!! lol

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

Yeah I did the last CircuitClub event at Wakefield day earlier this year (Australia Day). That was my first trackday where I could get in the car and just drive it all day long without needing to adjust anything. My best was 1:18sec so need to find quite abit of time somewhere hehe...

would have loved to come out to this.

Hello Kitty has been sitting the garage for 6 months now due to lack of funds....

Should hopefully be back out to wakefield in the next couple of months.

Well i'm off to the EC sprint on the 18th too, so no excuses about being rusty! Will have to think of another excuse before then...

:thumbsup:

Ill be there too, In the "Im old and scared white group", LOL.

No bourbon and talking this time.....just epic skids

hey you, dont encourage him, ill be tuning in the morning then ill have a good crack.

the old girl is alot better behaved than last time you saw her.

and whats this about a missus?

Yeah next round of SSCC @ E/C!!! I am heading back past from the Blue Mountains on the Sunday and thinking of coming in and seeing how everyone is going, not sure if the missus will agree though :(

Rusty!??? Mate you will be ace! No stress required, with all your little tweaks and hopefully alignment sorted = FLYING!!! Dont show the car fear, show it who's boss!!! :thumbsup:

Hopefully you can knock a few seconds off both your E/C & Wakey times!!!

Just keep ahead of Stu!! lol

Missus = g/f not wife lol

Mate i am sure you have got your car dialled in and running like a dream now! Really keen to see it again in action! Did the rear wing help with the rear traction/stability at all? Got rid of that epic trail braking issue?

would have loved to come out to this.

Hello Kitty has been sitting the garage for 6 months now due to lack of funds....

Should hopefully be back out to wakefield in the next couple of months.

I know that feeling... it was over 12 months between visits to the track for me in 07/08 due to lack of funds. :(

Be sure to let us know when it's going back out, very keen to see it!

yeh your right foot lol :P

Yeah I did the last CircuitClub event at Wakefield day earlier this year (Australia Day). That was my first trackday where I could get in the car and just drive it all day long without needing to adjust anything. My best was 1:18sec so need to find quite abit of time somewhere hehe...

really poor alignment solved most of the issues. going to tweak it again next weekend.

Missus = g/f not wife lol

Mate i am sure you have got your car dialled in and running like a dream now! Really keen to see it again in action! Did the rear wing help with the rear traction/stability at all? Got rid of that epic trail braking issue?

anyone one thinking of making a weekend of this, or is everyone just heading down on sunday morning?

i was thinking of heading down saturday and taking the girls to the Zoo, staying overnight somewhere and then heading to track. What time are we expected at the track? Otherwise i guess i would be leaving the gong at 5.30 sunday morning. Takes about a hour and a half correct?

anyone one thinking of making a weekend of this, or is everyone just heading down on sunday morning?

i was thinking of heading down saturday and taking the girls to the Zoo, staying overnight somewhere and then heading to track. What time are we expected at the track? Otherwise i guess i would be leaving the gong at 5.30 sunday morning. Takes about a hour and a half correct?

Yeah about an hour and a half from the Gong I belive.

The driver's briefing is supposed to be at 9, but usually starts a little after. If you do decide to leave Sunday morning, I reckon you can leave a bit later. There's no scrutineering, which saves a fair bit of time. For CC days, I normally aim to get there at 730, and even that is plenty of time.

im not sure to be honest, but your more than welcome too. I dont really do anything to it besides put fuel in it....its quite a boring car to pit for. Im going to wheel align it and give it a service this weekend. I think it will only be tyre pressures and fuel on the day, unless i have some missfortune and we have to emergency cable tie panels back on lol.

9am driver brief......means i can leave at 6.30. gold.

Stu...Do you need any help that weekend?

stu... remind me, do you run semi's? if so! I'll need some tyre pressure advice! I've never run on them before and I'll use them if I can find some decently priced semi's before next weekend

Well i'm off to the EC sprint on the 18th too, so no excuses about being rusty! Will have to think of another excuse before then...

I'm taking a mate out as a passenger at this Wakefield day too, so better be on my best beahviour. :(

Awesome Pic of your car (ex andos car) in the SSCC Mag!! :)

Better come say hi if I dont see you first on sunday!! I will be peddling Streetys Grey Evo...Race No. 424!

yeh i do but im not the best person to ask. Ive only driven on them twice, i was starting at 26psi cold and seeing where they end up hot, some of the other boys will no what is ok.

stu... remind me, do you run semi's? if so! I'll need some tyre pressure advice! I've never run on them before and I'll use them if I can find some decently priced semi's before next weekend
hey - ask Ivan or Jayne about NOel's spot, apparently he didn't pay and asked me if he was still coming, so his spot may still be abailable.

As far as I know I'm comin lizzie. If theres a prob with payment let me know by text if you would please mate.

currenty in sydney till tomozz then goneski back to goulburn.

Sydney sux wang.




  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...