Jump to content
SAU Community

Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 4 weeks later...

Hi Donnan,

Sorry for the late reply, I have been interstate.

Not separting the pump from the motor at this stage.

Do you have the power steering pump? How much, including postage, to Canberra?

Would you have the LHS glass window seal that's on the car, the window seals against it when you close the door - in good condition, no cracks ect. Sorry not sure what you call it.

I'd like the drivers side as well if both are in good condition and the price is right.

Cheers,

Attached this photo so you have an idea what I'm talking about.

post-49720-1275706154_thumb.png

Edited by Jaredo

fark seeing this mates me wanna cry as to how cheap i sold my slightly damaged skyline :)

oh well BTW this was a tough looking skyline, pitty someone didn't buy it as one unit and kept it

Congrat to the owner, looks like a well maintained car

Hehe yeh it sucks to have had to strip it apart and sell it off!

Car got towed away last night, i almost shed a tear :P

Hopefully the new owner puts some work into it and it comes back better than before.

fark seeing this mates me wanna cry as to how cheap i sold my slightly damaged skyline :rofl:

oh well BTW this was a tough looking skyline, pitty someone didn't buy it as one unit and kept it

Congrat to the owner, looks like a well maintained car

Well few more things sold.

Gearbox, coilovers and headlights now gone.

Only things left now as below. Will get some pics soon for the rims.

18x8, 18x9 Volteks with average rubber on them - $800 (pics coming)

RB25DET with engine loom. Missing coilpacks, turbo, oil and water lines. Comes with a set of standard injectors - $1000

R33 S1 front reinforcement bar - $60

Once I do a clean up, might be some other random stuff there.

  • 4 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...