Jump to content
SAU Community

Nismo Badge On Boot

diamondjo

By diamondjo,
in Exterior & Interior Styling

 Share

Recommended Posts

diamondjo Collaborator

diamondjo

Posted
Posted

So I just put a deposit on my second Skyline (YAY!) - the first one being damaged in the hail storm - it's another R33 GTS25t.

Now, I noticed that it has a nismo badge on the top right hand side of the boot lid - where the GTS25t sticker would normally be. I've done a search and discovered that there are in fact a number of cars like this which makes me wonder - does this badge denote anything different in the spec of the car? Or maybe it was just a trendy thing to do in Japan: remove the GTS25t sticker and pop a Nismo badge on it. Thing is, the badge is aligned so perfectly and there are no marks on the paint to indicate a sticker was once there - I just want to know what (if anything) the badge means ;)

Link to comment
https://www.sau.com.au/forums/topic/316094-nismo-badge-on-boot/
Share on other sites
GTR-N1 Grand Master

GTR-N1

Posted
Posted
...and there are no marks on the paint to indicate a sticker was once there. :blink:

The old one can get pretty crappy.

The fact that you can't see any evidence of the original sticker means that the owner did a good job of removing it with great care > followed by polishing the area.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Predator1
      Rb26 iron block limit

      By Predator1 · Posted

      Why not? Since mines been built, I've used low boost maybe 5 times.
    • GTSBoy
      gauge needle removal

      By GTSBoy · Posted

      Yeah, so widen your search to any Nissan speedo first, then go wider if needed. I will say though, that there is a better than even chance that what I said first will likely come into play. They quite possibly won't come apart without damage. I tried to disassemble a stepper gauge that I wanted to repair. There was no way that needle was coming off the spindle, and I could not see how the spindle would come out of the mechanism behind. Assembled once, never to be disassembled, was my conclusion. Could be the same on the R34 cluster. Failing that - take the cluster to a workshop that specialises in automotive instrument work. There's usually at least one in every Australian city. They'll either be able to do it for you for small cost, or tell you it can't be done. It might be that "it can't be done" unless you follow some arcane procedure, including trickiness to glue it back together or something, that only experienced techs know.
    • GTSBoy
      R-chassis INNER tie rod torque spec?

      By GTSBoy · Posted

      Well, given that I, an engineer, almost never bring out the torque wrench to tighten up chassis bolts, despite fully knowing the theory, and instead rely on feel, which I happen to know is exactly how the majority of mechanics do things, should tell you the level of actual peril that exists from not achieving exactly 88 Nm of torque. How about if I just say then that 88Nm is at the lower end of the correct wheel nut torque range? Everyone knows how to tighten a wheel nut, right? And almost no-one ever brings out the torque wrench for that task
    • hardsteppa
      R-chassis INNER tie rod torque spec?

      By hardsteppa · Posted

      Don't be ridiculous. "2-3 ugga duggas or one Oof. You have to use Oof on tie rods because you can't get an ugga dugga on there." Is not helping the guy at all.
    • JC71
      gauge needle removal

      By JC71 · Posted

      I have done a lot of research before posting here and on gtruk forum. couldn't find anything. I have my gauges all part except the needle itself. the needle has a extremely small hole in the center, but the shaft going to the needle is extremely small and appears to have nothing to index it either. doesn't seem strong enough to simple pry or pull without damaging something. Already tried the old spoon trick on a extra triple meter I have from a gtt, but no luck. the center cap comes off easily but the hole in the meter face plate aren't big enough to get over the needle itself. figured this would be my best place to find someone who might have actually removed theirs. wonder if there is some type of small pin press tool to push the pin in while pulling the needle base off.
×
×
  • Create New...