Jump to content
SAU Community

Change Gtst Into A 4wd

max.89
 Share

Recommended Posts

Jamezilla Grand Master

Jamezilla

Posted
Posted

Yes - should be wasteland.

But... Fireworks are illegal in VIC. You are NOT allowed to sell them. So PLEASE no-one post that you have some available. Use PM.

You can buy them in ACT, but you have to be a non-ACT resident and remove them from ACT to another state within 6 hours after purchase - where they are illegal to use. Silly isn't it.

Nutshell - buy them in Canberra, bring them home - use them whilst exercising discression (if at all possible for pretty expolsives) :)

Also - when in ACT, remember to get some porn too.

Link to comment
Share on other sites
predator Grand Master

predator

Posted
Posted

nah - don't you have to actually be an ACT resident, and show an ACT drivers license to get them now??

Thats what i heard anyhow.

Plenty of illegal ones around QLD on new years, so somebody is getting them from somewhere.

Try chinatown.. bring an asian friend :)

Link to comment
Share on other sites
Jamezilla Grand Master

Jamezilla

Posted
Posted

Pred: Nope. ACT residents aren't allowed.

This... ah... guy I know, bought some on the way back from Sydney at New Years. Had to show VIC licence (a copy was taken) and sign a form saying the fireworks were leaving the ACT within 6-hours.

Needless to say I... I mean, he... has used them all up :)

Link to comment
Share on other sites
max.89 Contributor

max.89

Posted
  • Author
Posted

6 hours after purchase ?

wtf.. ohh new laws..

dang..last time i was in canberra.. i bought a shitload, and i used to order them over the net.. i even tryed bribing them with a $50tip..

They all thought about it, and then tryed to raise it.. and double the price of the fireworks..

VIC is so crap :)

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      R32 GTST - 600KW+ RB28/CD009 Build

      By Dose Pipe Sutututu · Posted

      Feels like most tend to keep it under 8000rpm for hydraulic lifters. Quick search on the net and those on Rennlist like to keep theirs under 7500rpm, Speed Talk under 8000rpm. Perhaps start to take timing out for 7250rpm and soft cut it by 8000rpm.
    • PranK
      Elevated lead levels in oil - Engine on borrowed time?

      By PranK · Posted

      Ok, so I just had a chat with my mechanic. He said there is no real source of lead in the engine, the bearings and pistons are aluminium and the rings I think he said are steel. He doesn't recall what additive he used but that along with the thicker 20w50 he used could be a source of lead. It's put me at ease a little bit and I guess I'll just have to wait 5000 k's to do another change and see if anything is different.  I appreciate you guys chiming in. I have a habit of immediately thinking worst case with things like this.
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Finished street tuning it to 20psi with WMI. Haltech really makes it easy for you with those 4D maps. I have 17psi springs in my gates but they seem to only start cracking around 17 and taper off around 19/20psi. I was originally on 14psi springs but I'm expecting to need ~35-38psi to hit my goal and I was worried It wouldn't make it. Dyno's booked for next Friday. All I have left is to replace my el cheapo amazon special type k connectors on my EGT's. They have no strain relief and well are just all around cheap compared to what I use at work. I had the wires in one get lose and I don't want a repeat of that on the Dyno. I also want to figure out why I have 4 cylinders that are perfectly identical, one that's 30C over and another that's 30C under. I'm chocking this up to EGT position in the runners not being identical and will verify that as well. Wish me luck! Hopefully I make all the power with no bang. Question for the group, I have my rev limiter set to 8000rpm. I have a fully built head and new lifters but I stuck with hydro's. Is 8000 fair or am I being to cautious? 
    • hattori hanzo
      A To Z Imports - Gold Coast

      By hattori hanzo · Posted

      Anyone used A to Z Imports in Goldcoast?  I was referred to them for engineering and RWC? However besides a few one off bad google reviews it all seems pretty legit?   https://www.atozimports.com.au/
    • DrR34Gtr
      Rb26 stroker Piston Kit 2.8 77.7mm

      By DrR34Gtr · Posted

      RB26 JE pistons to suit 2.8 stroker crank 77.7mm and 86.5mm bore Custom made with EN plating and Je perfect skirt.  Valve pockets Suits 1mm over valves biggest lift you can throw at them. 21mm 210” wall 9310 upgraded wrist pins to suit standard sized 121.5mm rods. I had these made for my build but block had to be rebored to a larger size so sadly I can no longer use them. I spent a-lot of time and money on these pistons.  See photos these are the Heavy duty forging in 2618 material with all the bells and whistles accumulator grooves double force fed pin oilers skirt milling window milling etc.  The En plating was done to the whole piston this helps with heat and also critically in the ring grooves to prevent ring micro welding. The Perfect skirt is JE's propriety coating its a permanent coating that expands and contracts with the bore to prevent piston slap and noise and also friction. you can look these features up.  They have been balanced to a tenth of a gram at my expense. They come with Gas nitrided ring pack's and oil ring rail supports all brand new never used. The Dome volume is 17.9 cc which based on your Gasket thickness and chamber volume can put you anywhere you like in terms of Comp ratio in my case it was just under 9:1 but this is highly customizable for your build.  In terms of sizing these pistons will work with any 77.7mm build using the normal sized rods.  I did buy an extra set of rings at the time of purchase incase i stuffed one up during gapping so i will throw these in at my expense. I purchased these through performance wholesale in Brisbane and still have the receipt if you were to make these now it would cost more then double what i have them listed for. I am super fussy when it comes to building motors so you will see they have been measured and numbered with marker in the photos. Every thing has been handled and stored with the utmost care and diligence. looking for 2350 ONO any question please ask. test is better 0450 428 895 they will be sent via registered post anywhere in Aus free international buyers contact for quote.  
×
×
  • Create New...